565917
7
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
English
6
Fig. 5
2. Cutting fixed lengths
When cutting several studs to the same length,
using the equipment in the following way will making
cutting operations more efficient.
(1) First cut one stud to the required length, and then
use it as a fixed length guide.
(2) Insert the stud used as a fixed length guide in the
stud attachment hole found on the main unit stud
guide and use the hexagonal bar wrench to tighten
and secure the hex. socket hd. bolt. Adjust at this
time so that the distance between the end of the
stud used as a fixed length and the cutter is the
necessary length.
(3) Insert the stud for cutting in the cutter, aligning the
end with that of the stud used as a cutting guide,
and then cut the stud.
Fig. 6
3. Cutting studs that are already secured
When cutting studs that are suspended from the
ceiling or secured to walls or floors.
When inserting the stud in the cutter, the meshing
of the stud thread and cutter thread is unstable. In
such a case, after inserting the stud in the cutter,
lightly pull the trigger switch to close the cutter at
low speed and then completely mesh the stud and
the upper and lower cutters. Next, pull the trigger
switch all the way to cut the stud.
CAUTION
Use your left hand to hold the stud on the side
released by cutting to insure that it does not fall
unexpectedly.
Fig. 7
4. Removing the stud from the unit during cutting
operations
If you wish to remove the stud from the cutter
during cutting operation, pull the trigger switch
while pressing the forward/reverse-switching button
toward the side of
(Fig. 1-2), and then the motor
will run in reverse, allowing you to remove the stud
from the cutter. (Fig. 8)
CAUTIONS
When removing a stud that is suspended from
the ceiling, hold the main unit with both hands
to prevent any possibility of the stud falling.
Immediately turn off the switch once the cutter
is free from the stud. If you attempt to do this
with the switch turned on, the cutter might cut
into the stud again.
If you leave the switch on in a state where the
cutter is cut in the stud, some forced pressure
can be applied to the main unit, resulting in
damage.
When you operate the forward/reverse-switching
button at the position of
(Fig. 1-2), do not
release your finger from the forward/reverse-
switching button until the switch is turned off.
If you release your finger before the switch is
turned off, there can be a case where the bracket
(A) does not stop immediately.
Fig. 8
5. Using the hook
The hook can be used to hang up the unit temporarily
during operations (Fig. 9).
CAUTION
The hook should never be used to hang the unit
on your person.
When using the hook, check to make sure that the
main unit will not slip and fall, or become unstable
by the wind, etc.
Never hang the unit from your belt or trousers as
this could cause accidents.
Cutter
Bracket (B)
Stud
Correctly mesh
Necessary length
Hex. socket hd. bolt
Fixed length
guide (First cut
the stud to the
required length)
Stud
Stud
attachment hole
Stud suspended
from the ceiling
Forward/reverse
switching button
Trigger switch
01Eng_CL10SA_WE 08/12/15, 11:576
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CL10SA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CL10SA in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info