565917
5
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
English
4
2. Trimmer
Optional accessories are subject to change without
notice.
APPLICATIONS
Cutting of soft steel studs
PRIOR TO OPERATION
WARNING!
Before use, check the following items. Concerning items
1-7, always be sure to check them before plugging the
power cord into the receptacle.
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
CAUTION:
Damaged cord must be replaced or repaired.
4. Preparation and confirmation of working environment.
Check and confirm if the workplace is in proper
conditions as mentioned in the general operational
precautions item 1.
Screw size
M10 × 1.5
M8 × 1.25
M6 × 1
W3/8" × 1.5875
5. Setting the forward/reverse switching button
(1) As illustrated in Fig. 1-1, the forward/reverse
switching button ordinarily lies at the position of
(Fig. 1-1), enabling cutting operation.
(2) If you press in the forward/reverse switching button
from the left as shown in Fig. 1-2 at the position
of
(Fig. 1-2) and slowly pull the trigger switch
while pressing the button, the cutter can be removed
from the stud. Keep the button at this position only
when you remove the cutter from the stud during
cutting operation. As soon as the cutter is removed
from the stud, turn off the switch. If you release your
finger, the forward/reverse switching button will
automatically return to the position of
(Fig. 1-1).
CAUTION
Do not attempt to cut in the
position (Fig. 1-
2). If you attempt to cut in this position, there will
be an overload on the motor and cutting will not
be possible. Never apply excessive force to the
main unit as this can cause damage to the unit.
When you operate the forward/reverse-switching
button at the position of
(Fig. 1-2), do not
release your finger from the forward/reverse-
switching button until the switch is turned off. If
you release your finger before the switch is turned
off, there can be a case where the bracket (A) does
not stop immediately.
Fig. 1-1 Fig. 1-2
Forward/reverse switching button
(Equipment as seen from the handle side)
Removal during
cutting operations
During cutting
operations
OPTIONAL ACCESSORIES (sold separately)
1. Cutter
Screw size Combining cutters and spacers
M10 × 1.5 M10 Cutter ............................. 2
M10 Spacer ............................ 2
M8 × 1.25 M8 Cutter ............................... 2
M8 Spacer .............................. 2
M6 × 1 M6 Cutter ............................... 2
M6 Spacer ............................. 2
W3/8" × 1.5875 W3/8" Cutter ........................... 2
01Eng_CL10SA_WE 08/12/15, 11:574
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi CL10SA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi CL10SA in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 1,59 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info