Handleiding Hikoki VB3616DA (pagina 17 van 192) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins)

816254

Verklein

Vergroot

Pagina terug

1/192

Pagina verder

English

OPERATION

CAUTION

Pull out battery before carrying out any adjustment,

servicing or maintenance.

When ﬁ nished with a job, pull out the battery.

1. Switch operation

This product is equipped with a switch lock to prevent

inadvertent switch operations. (Fig. 7-a)

Pressing the switch lock in one of the indicated directions

and pulling the switch will activate the motor.

Once the switch is activated, it will remain on even after

releasing the switch lock as long as you are pulling on

the switch.

Releasing the switch within area Ⓐ will apply a brake

that will stop operation. (Fig. 7-b)

Releasing the switch within area Ⓑ will automatically

return the upper cutter and bending roller to their original

positions. (Fig. 7-b)

WARNING

The cutter also simultaneously activates, so please

close the cover. (Fig. 7-b)

2. Reverse-rotating the cutter and bending roller

Releasing the switch during operation could result in

the cutter and bending roller coming to a standstill to

sandwich the rebar and irremovably lock it in place.

(Fig. 8)

In this situation, the motor should be reverse-rotated to

return the cutter and bending roller back to their original

positions.

Below are the two methods for returning the cutter and

bending roller during operation.

● Set the setting dial on “RETURN” (Fig. 8-a)

(1) Align the setting dial on “RETURN”.

(2) Pulling the switch again will activate reverse-rotation

mode.

When the tool begins returning, it will return to its original

position when the switch is released.

● Press the Manual Mode switch (Fig. 8-b)

(1) Press the Manual Mode switch.

(2) Pulling the switch again will activate reverse-rotation

mode.

The tool will return while the switch is pulled, and it will

stop when it returns to its original position.

(3) Once returned to the original position, press the Manual

Mode switch to return to “Normal Rotation Mode”.

NOTE

The tool will not operate if left in Reverse-rotation mode,

so press the Manual Mode switch to cancel reverse

rotation.

HOW TO USE (CUTTING)

WARNING

○ Note that the unit is not a hand held tool. Be absolutely

sure to use the unit only after placing it on stable spots

such as ﬂ oor, ground, etc.

○ Never bring your hand close to the cutter during

operation.

○ Never bring your hand close to the reaction stoppers A

and B during operation.

1. Inspect the cutter and grip rubber

WARNING

○ Conﬁ rm that the hexagon socket bolt attaching the cutter

is tight.

If the tool is used with the bolt loose, it could damage the

tool or the cutter and result in accident or injury.

○ The machine is so designed that the upper cutter and the

grip rubber can support a rebar.

If the grip rubber gets worn out, there is a fear that it

cannot suﬃ ciently hold the rebar and gets broken down

with its parts ﬂ ying around, etc.

If the grip rubber cannot hold the rebar much longer,

replace it with a new grip rubber. (For replacing the grip

rubber and repairing, ask the store where you purchased

it or the HiKOKI Authorized Service Center.)

(1) Position the tool as shown in Fig. 9.

(2) Attach battery and battery cover. (Fig. 10)

(3) Open the cover. (Fig. 12)

(4) Lower the upper cutter.

Lightly pull the switch and slowly move the upper cutter.

When the upper cutter comes outside the cam cover and

the hexagon socket bolt is fully visible, release the switch

to stop it in that position. (Fig. 13)

(5) Detach the battery cover and battery. (Fig. 11)

(6) Check for abnormalities such as wear, deformation or

breaks in the cutter. (Fig. 14)

If the cutter needs to be exchanged, see “3. Cutter

Replacement”.

(7) Using the included hexagonal bar wrench, make sure

that the hexagon socket bolt is fully tightened. (Fig. 15)

(8) Make sure the grip rubber isn’t worn down (Fig. 16)

(9) Make sure that the switch lock is in the lock position

(Fig. 17)

(10)

Attach battery and battery cover (Fig. 10)

2. Cutting

WARNING

○ Do not cut any materials other than the rebars. If you

attempt to do so, the material can splinter into pieces

and scatter.

○ The bending roller moves even during cutting operation.

Never bring your hand close to the bending roller.

○ The cutter blade can get worn out by repeated cutting of

the rebar. Continued use of a worn-out cutter can result

in the damage and the broken pieces ﬂ ying around.

Replace it with a new cutter after approximately 8000

times of cutting as a rough guide.

○

During cutting work, securely

hook the rebar to the reaction

stopper B. Furthermore, secure

enough length of the rebar to be

hooked to the reaction stopper B.

○ Set the rebar in the center or the

recess of the cutter during cutting

work. Any cutting work with the rebar

set on corners or ends of the cutter

can result in the pieces of broken

rebar ﬂ ying around or the damage to the cutter and the

machine.

CAUTION

○ Do not simultaneously cut two rebars measuring

D16 mm or D13 mm.

Doing so may damage the tool.

○ A slip clutch is built in the machine to protect the

mechanism.

If you process the material with the diameter or quality

beyond the capacity, the slip clutch can sometimes

function. In such a case, stop processing immediately

and check the material.

When the slip clutch works, a big slip noise occurs, but

it’s not a malfunction.

After following the steps for “1. Inspect the cutter and grip

rubber” (steps (1) through (10)), follow the instructions

below.

(1) Position the setting dial in the “CUT” position. (Fig. 18)

(2) Set the rebar to be cut above the lower cutter

Make sure that there is enough length for the rebar to

fully hook reaction stopper B. (Fig. 19)

(3) Press the switch lock in either direction to release the

lock, and pull the switch to cut the rebar. (Fig. 7)

After cutting the rebar, hold down the switch until the

motor completes its reverse-rotation and the upper

cutter begins its return.

0000BookVB3616DA.indb170000BookVB3616DA.indb17 2023/02/1715:02:582023/02/1715:02:58

Hikoki VB3616DA Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info