700148
21
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
Switch position = LP
21
OPERATING INSTRUCTIONS
INTERCONNECTION EXAMPLE: Master/Slave Mode
MASTER/SLAVE-Mode
NOTE: The GENERATION X4 Master/SLAVE-Mode only works with two similar X4-Amplifier-Models.
INTERCONNECTION MASTER
Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
If your headunit is equipped with a additional subwoofer lineout (SUB OUT), it is recommended to use this lineout.
Connect the remote wire (REM) to the remote terminal (REM) of the MASTER amp.
If required connect the enclosed bass remote wire only on the REMOTE IN port of the MASTER amp.
Don’t use the REMOTE OUT port in MASTER/SLAVE mode.
INTERCONNECTION SLAVE
Connect the RCA jacks SLAVE IN/OUT of the MASTER amp with the RCA jacks SLAVE IN/OUT of the SLAVE amp with appropriate
high-value RCA cables.
Connect the remote wire (REM) of the remote terminal (REM) of the MASTER amp with the remote terminal (REM) of the SLAVE amp.
Use therefore cable with a minimum profile section of 0,5 mm
2
.
• Connect the PROTECT BRIDGE port of the MASTER amp with the PROTECT BRIDGE port of the SLAVE amp with the enclosed
PROTECT BRIDGE wire.
INTERCONNECTION SUBWOOFER
• Check page 22.
SETTINGS MASTER
• The OPERATION MODE switch should be in LP position.
Please note the information of LOW PASS, SUB SONIC, PHASE, LEVEL, SUB BOOST, FREQ RANGE, Q-CONTROL and BASS
REMOTE on page 20.
SETTINGS SLAVE
• The MODE switch must be in SLAVE position.
In the SLAVE mode all controllers of the SLAVE amp are without function.
Only the already modified audiosignal of the MASTER amp will be amplified.
1. Connect Stereo RCA output (L/R or SUB OUT)
of the headunit with the LINE INPUT L/R of the
MASTER amp
Connect the bass remote controller
and the remote terminal on the
MASTER amplifier (REMOTE IN)
with the enclosed cable .
Switch position = MASTER
SLAVE
MASTER
Switch position = SLAVE
Remote wire REM Remote wire REM
Protect Bridge wire
Remote wire REM
2. Connect Stereo RCA output (MASTER OUTPUT)
of the MASTER amp with the SLAVE INPUT of the
SLAVE amp
1.
2.
Protect Bridge wire
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hifonics X4-Atlas bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hifonics X4-Atlas in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 3,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info