502558
46
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
46 OPERATION
Operation
Output Level Adjustment
With Source Signals
Normal output level adjustment for the
AVR is established using the test tone, as out-
lined on page 36. In some cases, however, it may
be desirable to adjust the output levels using
program material such as a test disc, or a selec-
tion you are familiar with. Additionally, the out-
put level for the subwoofer and those for the
Stereo modes can only be adjusted using this
procedure. Note that all adjustments made with
any input will be effective with all inputs select-
ed, just as it is the case with the adjustment
using the test tone.
To adjust the output levels using program materi-
al, first select the surround mode for which you
want to trim the speakers (see NOTE below), start
your program material source and set the
reference volume for the front left and front right
channels using the Volume Control
d
I.
Once the reference level has been set, press the
Channel Select button
C
Ù
and note that
FRONT L LEVEL will appear in the Lower
Display Line
˜
. To change the level, first
press the Set button
F
@
, and then use the
Selector buttons
7$
or the
/
¤
buttons
E
to raise or lower the level. DO NOT use the
volume control, as this will alter the reference
setting.
Once the change has been made, press the Set
button
F
@
and then press the Selector but-
tons
7$
or the
/
¤
buttons
E
to select
the next output channel location that you wish to
adjust. To adjust the subwoofer level, press the
Selector buttons
7$
or the
/
¤
buttons
E
until WOOFER LEVEL appears in the
Main Information Display
˜
or on-screen
display (only available if the subwoofer is turned
on).
Press the Set button
F
@
when the name of
the desired channel appears in the Main
Information Display
˜
and on-screen
display, and follow the instructions shown above
to adjust the level.
Repeat the procedure as needed until all
channels requiring adjustment have been set.
When all adjustments have been made and no
further adjustments are made for five seconds,
the AVR will return to normal operation.
The channel output may also be adjusted using
the full-OSD on-screen menu system. First, set
the volume to a comfortable listening level using
the Volume Control
ı
d
I. Then, press
the OSD button
L
to bring up the MASTER
MENU
(Figure 7). Press the
¤
Button
E
four
times until the on-screen cursor is next to
the
MANUAL SETUP line. Press the Set
Button
F
, select the CHANNEL ADJUST
line and press the Set Button
F
to activate the
CHANNEL ADJUST menu (Figure 22).
Figure 22
When the menu appears, the internal test tone
will be turned off.This will allow you to use your
external test disc or other source material as the
test signal. Then, use the
/
¤
Buttons
E
to
select the channels to be adjusted. At each
channel position use the
/
Buttons
E
to
change the output level.
Remember, when you are using a disc with test
signal (e.g. pink noise) or an external signal
generator as the source, the goal is to have the
output level at each channel be equal when
heard at the listening position, with any surround
mode selected. When your test source is a
normal disc with music signals, you may adjust
the level for each channel and surround mode as
you prefer, e.g. you may lower the center channel
level when you find it to be too high or increase
the level of the rears when you find it to be too
low with specific surround modes.
If you wish to reset all the levels to their original
factory default of 0dB offset, press the
/
¤
Buttons
E
so that the on-screen cursor is
next to the
LEVEL RESET line and press
the
/
Buttons
E
so that the word ONis
highlighted. After the levels are reset, resume the
procedure outlined above to reset the levels to
the desired settings. When all adjustments are
done, press the
/
¤
Buttons
E
to move the
on-screen cursor so that it is next to
BACK
TO MANUALSETUP
and then press the
Set Button
F
if you wish to go back to the
main menu to make other adjustments. If you
have no other adjustments to make, press the
OSD Button
L
to exit the menu system.
NOTE: The output levels may be separately
trimmed for each digital and analog surround
mode. If you wish to have different trim levels for a
specific mode, select that mode and then follow the
instructions in the steps shown above.
With Stereo modes the adjustment procedure
described above is the only way to trim the out-
put level, e.g. to match the Stereo level with
other modes.
EzSet/EQ On/Off
If you wish to turn the filter settings established
by EzSet/EQ on or off to demonstrate the impact
EzSet/EQ has on the sound of your system,
simply press the EzSet/EQ On/Off button
e
.
Using this feature does not change the settings;
it merely puts them in or out of the signal path.
Dim Function
Since the AVR will often be used when movies or
other video programming is viewed under low-
light conditions, you may wish to lower the
brightness of the front-panel displays and indica-
tors so that they do not distract from the video
presentation. You may dim the displays using the
menu system, as shown on page 47, or you may
control the brightness directly from the remote.
Simply press the Dim Button
D
once to dim
the front panel to half the normal brightness
level; press it again to turn the displays off. Note
that when the displays are dimmed or turned off,
the blue lighting around the Standby/On
Switch
3
will continue to stay lit as a reminder
that the AVR is still turned on.
The accent lighting for the Volume Control
ı
will remain at its normal level, rather than dim
when the panel displays are at half brightness.
Note that all changes to the front-panel bright-
ness level are temporary; the displays will return
to full brightness after the AVR is turned off and
then on again. To return the displays to full
brightness without turning the unit off, press the
Dim Button
D
as needed until the displays
are on.
In addition to lowering the brightness of the
displays or turning them off completely, you may
wish to have them appear whenever a button on
the remote or front panel is pushed, and then
gradually fade out after a set time period. You
may do this by making the appropriate settings in
the
VFD FADETIMEOUT line of the
ADVANCED SELECT menu, as shown on
page 47.
Memory Backup
This product is equipped with a memory backup
system that preserves tuner presets and system
configuration information if the unit is turned off
completely, accidentally unplugged or subjected
to a power outage. This memory will last for
approximately two weeks, after which time all
information must be reentered.
* CHANNEL ADJUST *
FL : 0dB SBR : 0dB
CEN : 0dB SBL : 0dB
FR : 0dB SL : 0dB
SR : 0dB SW1 : 0dB
TEST TONE: AUTO OFF MAN
LEVEL RESET: OFF ON
CH ADJUST: GLOBAL
EZSET SETTINGS: OFF ON
BACK TO MANUAL SETUP
29851_AVR645_ENG 30/10/06 9:46 Side 46
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR645 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR645 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR645

Harman Kardon AVR645 Gebruiksaanwijzing - Nederlands - 68 pagina's

Harman Kardon AVR645 Gebruiksaanwijzing - Deutsch - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info