502558
30
Verklein
Vergroot
Pagina terug
1/68
Pagina verder
30 SYSTEM CONFIGURATION
System Configuration
Step 2. Select one of the two options shown
based on the way you wish to have the system
settings entered:
• In most cases, you will want to use the
Automatic mode, which calibrates the system
for speaker presence, speaker “size”, speaker
crossover, channel output level, speaker-to-
listener delay time and room equalization. To
choose this mode simply press the Set Button
F
, as the cursor is already pointing to
AUTOMATIC EQ DESIGN when the
menu appears on the screen.
Then press the Set Button
F
again when the
AUTOMATIC EZSET/EQ menu appears,
to continue to Step 3.
• If you wish to enter the speaker crossover
frequencies yourself, but want to have the
EzSet/EQ system test for and calibrate all the
other functions listed above, press the
¤
Navigation Button
E
to point the cursor
at
EZSET/EQ SETUP and then press the
Set Button
F
. Once the MANUAL
SETUP
menu (Fig. 18) appears, follow the
instructions on page 32 to enter your desired
settings for the Crossover Frequencies, and
then return to the
EZSET/EQ MAIN
menu. Press the
¤
Navigation Button
E
again so that the cursor is pointing to
MANUAL EQDESIGN and then press the
Set Button
F
. When the interim message
screen appears to remind you to set the
crossovers, make sure that the cursor is point-
ing to
CONTINUE and press the Set
Button
F
again since you have already set
the crossovers.
Step 3. The
FAR FIELD MEASURE
screen (Figure 17b) will appear with instructions
to place the microphone, if you have not already
done so. This screen is also the place to set the
master volume level. As noted on the screen, use
the Volume Control
ı
d
to adjust the vol-
ume level to –35dB, as shown on the line that
appears at the bottom of the menu when the
volume is adjusted. Press the Set Button
F
when the volume is set to the proper level.
Figure 17b
Step 4. The final menu screen before the
EzSet/EQ process starts is a warning screen
(Figure 17c) that serves as a reminder to keep
the room as quiet as possible while the system is
in use. Extraneous noise of any kind may
adversely affect the accuracy of the system’s
results. Do not talk while the test tones are
circulating, and if possible, turn off any ventila-
tion systems if the noise form the air flow is loud
enough for you to hear. Should an outside noise
such as a phone ringing occur during the test
process, we recommend that you rerun EzSet/EQ.
If you do not wish to start the test process at this
time, press the
/
¤
Navigation Button
E
to return to either the EzSet/EQ menu or the
Master Menu, and press the Set Button
F
.To
begin the EzSet/EQ Near Field measurements,
press the
/
Navigation Button
E
so that
ONis highlighted in reverse video, and press the
Set Button
F
.
NOTE: Once the EzSet/EQ process starts, the
volume control and Standby/Off switches are
temporarily disabled while the tests are in
progress. Do not adjust the volume or turn the
unit off until you see the on-screen message
change to indicate that EzSet/EQ is finished.
Figure 17c
Step 5. At this point you will begin to hear a
series of test tones circulate among all the
speakers in your system. While this is happening,
the AVR is reading the signal to determine which
speaker positions are active, what type of
speaker is present at each active position, what
the distance is from the listening position to each
speaker, and to begin to build a profile of the
impact of the room’s acoustics on the quality of
audio reproduction. When the test is completed
you will hear the tones stop, and the system will
pause fors long as a minute while the processor
makes its calculations. Do not be alarmed if the
“WARNING” message remains on the screen
after tones stop until a results message is
displayed as shown in Step 6 or 7, below.
NOTE: While these tests detect whether a
speaker is connected to a particular output, they
cannot determine whether the speaker is in the
correct position. (For example, it can tell whether
a speaker is connected to the Surround Right
output, but it cannot tell whether the speaker is
on the right or left side of your listening room.)
For that reason, we strongly recommend that you
try to listen as the tone circulates, matching the
name shown for each channel to the location of
the speaker. If a tone is heard from a speaker
position that does not match the on-screen
message, make a note of the incorrect speaker
connections. When the test process stops you will
see a message indicating the they Far Field
measurements are complete, but since there is a
connection error press the
¤
Navigation
Button
E
so that the on-screen cursor in
Fig. 7 is pointing to
RETURN TOMASTER
MENU
and press the Set Button
F
. At this
point, exit all menus and turn the receiver off.
Check all speaker wire connections and then
rerun EzSet/EQ.
Step 6. When the Far Field tests are complete a
message screen will appear to confirm if the pro-
cedure was successful or not. In most cases there
will not be any problems and you will see the
message shown in Figure 17d on your screen. If
the speaker positions shown match the actual
speaker layout in your system, press the Set
Button
F
to complete EzSet/EQ by performing
the Near Field Measurements. Continue the
EzSet/EQ process by pressing the Set Button
F
to take the Near Field measurements from
the front left, center and right speakers. By taking
this separate set of measurements, the AVR is
able to complete its view of the room’s sonic
signature and apply equalization as needed to
correct spikes and dips in the system’s response.
Continue these instructions with Step 8.
Figure 17d
* FAR FIELD COMPLETE *
EQ successful
Speaker config detected
FL : YES SBR: YES
CEN : YES SBL: YES
FR : YES SL : YES
SR : YES SUB: YES
DO NEAR FIELD
BACK TO MASTER MENU
WARNING !!
During measurement
please maintain silence
while several sound
bursts are heard.
START : OFF ON
BACK TO EZSET/EQ MODE
BACK TO MASTER MENU
* FAR FIELD MEASURE *
Place mic at ear level
near the listening
position at least 3 ft/
1m from any hard
surface.
Set volume to -35dB
CONTINUE
BACK TO EZSET/EQ MAIN
BACK TO MASTER MENU
VOLUME: -35dB
29851_AVR645_ENG 30/10/06 9:46 Side 30
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Harman Kardon AVR645 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Harman Kardon AVR645 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Harman Kardon AVR645

Harman Kardon AVR645 Gebruiksaanwijzing - Nederlands - 68 pagina's

Harman Kardon AVR645 Gebruiksaanwijzing - Deutsch - 68 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info