813561
16
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
16
17
The battery can be left in the charger; in this case
the LED display is lit green continuously. The charger
keeps the battery pack in a fully charged state.
INSTALLATION AND REMOVAL OF THE BATTERY
PACK IN/FROM THE DEVICE
WARNING: Make sure that the rotational
direction switch is in the middle position to
avoid triggering the switch while removing
or installing the battery pack.
INSTALLATION
Slide the battery pack into the device until it clicks
into place. Make sure that the battery pack is correctly
positioned and fully engaged. (see Figure 7/A+B)
REMOVAL
Press the battery pack release button and pull the
battery out of the device.
ATTACHING THE TOOLS
WARNING: TO AVOID THE RISK OF INJURY,
REMOVE THE BATTERY PACK FROM THE
TOOL BEFORE MAKING ANY
ADJUSTMENTS, REMOVING AN ATTACHMENT OR
INSTALLING A NEW ACCESSORY.
Make sure that the lower edge of the respective
tool attachment and power section of the base
device are aligned horizontally and then push the
attachment into the device until it clicks into place.
(see Figure 8/A-C)
REMOVING THE TOOLS
Slide the locking switch down to release the tool
from its docking place, then pull the attachment
forward and away.
ON/OFF AND ROTATIONAL DIRECTION SWITCH
The device is switched on and off by pressing and
releasing the ON/OFF switch. The harder the ON/OFF
switch is pressed, the faster the rotational speed.
The direction of rotation switch is used to set the
direction of the drill chuck forward for screwing in
screws or backward for their removal. It is located
above the variable ON/OFF switch.
To select the forward direction of rotation, press the
direction switch to the left (when viewed from the
rear).
To select the backward direction of rotation, press
the direction switch to the right (when viewed from
the rear).
NOTE: When changing the position of the rotation
direction switch, make sure that the ON/OFF switch
for speed control is not pressed in.
WORKING WITH THE DRILL ATTACHMENT
Secure the device against being switched on
accidentally by moving the direction switch
(into the middle position). There is a risk of
injury if the device switches on unintentionally.
1. Turn the chuck anti-clockwise until the drill opening
is large enough to insert the tool (drill bit holder).
2. Insert the tool as far as possible into the chuck.
3. Turn the chuck clockwise to clamp the tool.
4. To remove the tool, turn the chuck anti-clockwise
and pull it out of the drill hole.
Selection of the desired operating mode
You can use the torque setting ring to adjust the
power produced by the screwdriver.
1 - Low power
19 - High power
A. Drilling:
When ready to drill, set the torque adjustment
ring to the drill setting. Insert the drill set
corresponding with the material into the chuck.
You can use for drilling into wood, metal,
plastic, cement, ceramics or any other similar or
comparable material.
B. Screwing: If you want to use for screwing, set the
torque adjustment ring to the appropriate torque
setting. Before choosing the setting, pay attention
to the material you want to screw into. Insert the bit
extension or the flexible bit holder into the chuck.
You can use it to attach different screws and parts.
Setting the direction of rotation
The direction of rotation of the device can be
changed using the rotational direction switch.
(see Figure 2)
1. Wait until the device has come to a standstill.
2. Move the direction switch to the desired position:
Clockwise direction of rotation: → for drilling and
screwing in screws.
Anti-clockwise direction of rotation: ← for
removal of screws.
3. When you move the direction switch to the
middle position, the device is secured against
being switched on unintentionally. The direction
of rotation may only be changed when the
machine is at a standstill.
WORKING WITH THE OSCILLATION ATTACHMENT
Secure the device against being switched
on accidentally by moving the direction
switch (into the middle position).
M22606_HammersmithMultitool_Manual_V03_20220629_MM.indd 16M22606_HammersmithMultitool_Manual_V03_20220629_MM.indd 16 20.07.22 12:2120.07.22 12:21
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw HammerSmith M22606 Multitool bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van HammerSmith M22606 Multitool in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3.76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info