683782
15
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
J Key for pre-sweeper with pilot
lamp (green), optional*
Note: this key is only operable if
the Hakomatic is equipped with the
”pre-sweeper” option and the Hako
service center has programmed the
machine accordingly. Otherwise,
”-OP-” is displayed.
This key turns the pre-sweeper ON
and OFF. The green pilot lamp
alights if the pre-sweeper is turned
ON. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
K Key for brush drive with pilot
lamp (green)
turns the brush drive ON and OFF.
The green lamp alights if the brush
head is lowered and the brushes
rotate. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
47
L Key for squeegee and suction
turbine with pilot lamp (green)
is lowering/lifting the squeegee and
turns the suction turbine ON and
OFF. The green lamp alights if the
squeegee is lowered and the suc-
tion turbine turned ON.
In case of a malfunction the fault
lamp (F) alights and the error code
appears in the service display.
Note: After lift-up of the squeegee
the suction turbine continues ope-
ration for about 15 seconds and the
pilot lamp (green) in the key flashes.
This measure precludes soiled
water from flowing out of the sque-
egee or the vacuuming hose back
to the floor. If the soiled water tank
is filled up, the suction turbine is
switched off after approx. 3 to 5
seconds and the water supply of
the brushes interrupted. These
functions can be activated again
after discharge of the tank.
M Key for water flow reduction
is used to reduce the water
quantity supplied to the brus-
hes/pads. The water quantity
may be reduced by 7 stages
from 5.5 liters to 1.0 liter per
minute, each stage correspon-
ding to one lamp
N Key for water infeed with pilot
lamp (green)
is used to turn on or off the
water infeed. When switching on
the brushes/pads the last set
water quantity is supplied auto-
matically but may be modified
via the (M) and (O) keys. The tool
mode
features this memory function as
well. There, the water infeed may
be adjusted from 0.5l to 1.0l per
minute.
J Key for pre-sweeper with pilot
lamp (green), optional*
Note: this key is only operable if
the Hakomatic is equipped with the
”pre-sweeper” option and the Hako
service center has programmed the
machine accordingly. Otherwise,
”-OP-” is displayed.
This key turns the pre-sweeper ON
and OFF. The green pilot lamp
alights if the pre-sweeper is turned
ON. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
K Key for brush drive with pilot
lamp (green)
turns the brush drive ON and OFF.
The green lamp alights if the brush
head is lowered and the brushes
rotate. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
47
L Key for squeegee and suction
turbine with pilot lamp (green)
is lowering/lifting the squeegee and
turns the suction turbine ON and
OFF. The green lamp alights if the
squeegee is lowered and the suc-
tion turbine turned ON.
In case of a malfunction the fault
lamp (F) alights and the error code
appears in the service display.
Note: After lift-up of the squeegee
the suction turbine continues ope-
ration for about 15 seconds and the
pilot lamp (green) in the key flashes.
This measure precludes soiled
water from flowing out of the sque-
egee or the vacuuming hose back
to the floor. If the soiled water tank
is filled up, the suction turbine is
switched off after approx. 3 to 5
seconds and the water supply of
the brushes interrupted. These
functions can be activated again
after discharge of the tank.
M Key for water flow reduction
is used to reduce the water
quantity supplied to the brus-
hes/pads. The water quantity
may be reduced by 7 stages
from 5.5 liters to 1.0 liter per
minute, each stage correspon-
ding to one lamp
N Key for water infeed with
pilot lamp (green)
is used to turn on or off the
water infeed. When switching
on the brushes/pads the last
set water quantity is supplied
automatically but may be
modified via the (M) and (O)
keys. The tool mode
features this memory function
as well. There, the water
infeed may be adjusted from
0.5l to 1.0l per minute.
J Key for pre-sweeper with pilot
lamp (green), optional*
Note: this key is only operable if
the Hakomatic is equipped with the
”pre-sweeper” option and the Hako
service center has programmed the
machine accordingly. Otherwise,
”-OP-” is displayed.
This key turns the pre-sweeper ON
and OFF. The green pilot lamp
alights if the pre-sweeper is turned
ON. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
K Key for brush drive with pilot
lamp (green)
turns the brush drive ON and OFF.
The green lamp alights if the brush
head is lowered and the brushes
rotate. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
47
L Key for squeegee and suction
turbine with pilot lamp (green)
is lowering/lifting the squeegee and
turns the suction turbine ON and
OFF. The green lamp alights if the
squeegee is lowered and the suc-
tion turbine turned ON.
In case of a malfunction the fault
lamp (F) alights and the error code
appears in the service display.
Note: After lift-up of the squeegee
the suction turbine continues ope-
ration for about 15 seconds and the
pilot lamp (green) in the key flashes.
This measure precludes soiled
water from flowing out of the sque-
egee or the vacuuming hose back
to the floor. If the soiled water tank
is filled up, the suction turbine is
switched off after approx. 3 to 5
seconds and the water supply of
the brushes interrupted. These
functions can be activated again
after discharge of the tank.
M Key for water flow reduction
is used to reduce the water
quantity supplied to the brus-
hes/pads. The water quantity
may be reduced by 7 stages
from 5.5 liters to 1.0 liter per
minute, each stage correspon-
ding to one lamp
N Key for water infeed with pilot
lamp (green)
is used to turn on or off the
water infeed. When switching on
the brushes/pads the last set
water quantity is supplied auto-
matically but may be modified
via the (M) and (O) keys. The tool
mode
features this memory function as
well. There, the water infeed may
be adjusted from 0.5l to 1.0l per
minute.
J Key for pre-sweeper with pilot
lamp (green), optional*
Note: this key is only operable if
the Hakomatic is equipped with the
”pre-sweeper” option and the Hako
service center has programmed the
machine accordingly. Otherwise,
”-OP-” is displayed.
This key turns the pre-sweeper ON
and OFF. The green pilot lamp
alights if the pre-sweeper is turned
ON. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
K Key for brush drive with pilot
lamp (green)
turns the brush drive ON and OFF.
The green lamp alights if the brush
head is lowered and the brushes
rotate. In case of a malfunction the
fault lamp (F) alights and the error
code appears in the service display.
47
L Key for squeegee and suction
turbine with pilot lamp (green)
is lowering/lifting the squeegee and
turns the suction turbine ON and
OFF. The green lamp alights if the
squeegee is lowered and the suc-
tion turbine turned ON.
In case of a malfunction the fault
lamp (F) alights and the error code
appears in the service display.
Note: After lift-up of the squeegee
the suction turbine continues ope-
ration for about 15 seconds and the
pilot lamp (green) in the key flashes.
This measure precludes soiled
water from flowing out of the sque-
egee or the vacuuming hose back
to the floor. If the soiled water tank
is filled up, the suction turbine is
switched off after approx. 3 to 5
seconds and the water supply of
the brushes interrupted. These
functions can be activated again
after discharge of the tank.
M Key for water flow reduction
is used to reduce the water
quantity supplied to the brus-
hes/pads. The water quantity
may be reduced by 7 stages
from 5.5 liters to 1.0 liter per
minute, each stage correspon-
ding to one lamp
N Key for water infeed with
pilot lamp (green)
is used to turn on or off the
water infeed. When switching
on the brushes/pads the last
set water quantity is supplied
automatically but may be
modified via the (M) and (O)
keys. The tool mode
features this memory function
as well. There, the water
infeed may be adjusted from
0.5l to 1.0l per minute.
Scrubmaster is equipped with the
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hako Scrubmaster B140R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hako Scrubmaster B140R in de taal/talen: Engels als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info