683782
14
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
software status for 1 approx.
second, e.g.
last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
software status for 1 approx.
second, e.g.
last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
software status for 1 approx.
second, e.g.
last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Service display
The service display is located in the
hourmeter display.
When turning ON, the following
sequence of information will appear in
the hourmeter display:
software status for 1 approx.
second, e.g.
last error found, for approx. 2
seconds (points blink), e.g.
Note: If a defect is still existing, a
buzzer sounds and the red display
turns ON (F).
hours run, e.g. during operation, the
dot will blink.
Note: on factory-new machines,
the display may read when the key
switch is turned to ON.
This is an internal control code;
display will change to 0 hours after
not more than one hour.
The Hakomatic is serviceable with
this display.
Error display is active either.
If a malfunction occurs during ope-
ration, a 4-digit number will appear
in the display, the 4 dots will start
flashing simultaneously and the
buzzer sounds.
Refer to page 61 for the error code
numbers which you may remedy by
yourself. If the machine does not
operate correctly despite measures
taken, denote the error code and
advise your Hako service center.
H Pilot lamp for battery charge
condition
Upon turning ON the key switch, all
green pilot lamps (b to d) alight in
case of a perfectly charged battery.
During operation the lamps b, c and
d will successively extinguish as the
battery discharges.
A flashing red light (a) indicates that
operation will soon be interrupted
and the buzzer sounds. After 3
more minutes, the red lamp alights
permanently and the brush dive
and the suction turbine will be
switched OFF. The travel drive
assembly remains activated. We
recommend to recharge the batte-
ries at the charging station as soon
as possible.
I Key for additional scrubbing and
vacuuming tool
Note: this key is only operable if
the Hakomatic is equipped with
the ”additional scrubbing and
vacuuming tool” option and the Ha-
ko service center has programmed
the machine accordingly.
Otherwise, ”-OP-” is displayed.
This key turns the water pump and
the suction turbine ON and OFF.
The water and the vacuuming hose
of the scrubbing tool have to be
connected previously.
46
3. 0 1 5
1. 2. 6. 1.
0 2 1 5.
9 9 9 9.
Scrubmaster is serviceable with
Scrubmaster is equipped with
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hako Scrubmaster B140R bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hako Scrubmaster B140R in de taal/talen: Engels als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info