665711
24
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
24
TIG 220 DC / 300 DC
EN
Connection
The TIG 300 DC is equipped with a female socket for a remote control.
The specic 7 pin male plug (option ref.045699) enables connection to the different types of manual remote control or foot pedal. For the cabling
layout, please see the diagram below.
REMOTE CONTROL TYPE Wire description Pin
CONNECT-5
Foot pedal Manual remote control
5V A
Cursor B
Common/Earth C
Switch D
AUTO-DETECT E
ARC ON F
REG I G
Operating :
• Manual remote control (option ref. 045675)
The remote control enables the variation of current from 50% to 100% of the set intensity. In this conguration, all modes and functions of the
machine are accessible and can be set.
• Pedal (option ref. 045682) :
The pedal control enables variation of the current from the minimum set current to a 100% of the set intensity.
In TIG mode, the machine will only operate in two-stage welding (2T mode). The upslope and downslope are not automatic, and are controlled by
the User with the foot pedal.
• Connect 5 - automaton mode:
This mode enables to pilot the TIG 300 DC from a console or from an automaton due to 5 pre-saved programs.
As the foot pedal, the «Switch (D)» enables to start or stop welding according to the choosen cycle. The voltage value for the «slider (B)» matches
a program or the actual statut.
This voltage must be between 0 and 5V (step of 0.5V) which is linked to a program reminder:
- Actual status : 0 - 0.7V
- Program 1 : 0.8- 1.5V
- Program 2 : 1.6 - 2.2V
- Program 3 : 2.3 - 3.0V
- Program 4 : 3.0 - 3.7V
- Program 5 : 3.8 - 4.5V
An additional potentiometer enables to change the current (+/- 15%) either whilst welding or not. The information ARC ON (arc presence) enables
the automaton to synchonise itself (Pull Up 100k entry, automaton side). Put the pin AUTO_DETECT to the earth enables to start the product
without going through the window where you can select the type of remote control used.
The 5 programs loaded correspond to the frist 5 saved programs (P1 to P5).
Additional explanations are avialable on our website
(https://goo.gl/i146Ma)
.
COOLING UNIT
TIG 220 DC
WCU0.5kW_A
P 1L/min = 500W
Capacity = 1.5 L
U1 = 185V - 265V
When working within the 185V-265V power supply range, the cooling unit is controlled by the welding
machine,
When working within the 85V-185V power supply range, the cooling unit is always switched off.
WCU1kW_A
P 1L/min = 1000W
Capacity = 3 L
U1 = 85V - 265V
The cooling unit is controlled by the welding machine throughout the 85V-265V power supply range.
TIG 300 DC
WCU1kW_B
P 1L/min = 1000W
Capacity = 3 L
U1 = 400V +/- 15%
The cooling unit is controlled by the welding machine throughout the power supply range.
This machine may be connected to a cooling system for the cooling of the water torch. In the OPTION menu, this cooling unit system can be deac-
tivated.
A 3 second press on the
MEM
PROG
button allows access to the cooling unit system menu.
Make sure that the cooling unit is turned off before disconnecting the inlet and outlet hoses for torch liquid.
The coolant is harmful and irritates the eyesm the mucus membranes and the skin. Hot liquid may cause burns.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys TIG 300 DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys TIG 300 DC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info