665742
20
Verklein
Vergroot
Pagina terug
1/86
Pagina verder
EASYMIG 130 / 140 / 150
EN
20
Note : The machine’s duty cycle has been tested at room temperature (40°C) and has been determined by
simulation.
This is a Class-A device. It is designed to be used in an industrial or professional environment. In a different
environment, it can be difcult to ensure electromagnetic compatibility, due to conducted disturbances as well
as radiation.
RISK OF INJURY DUE TO MOVING PARTS
The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead
to injuries! Take extra care.
• Do not lay a hand to swivel or moving components or parts to the drive!
• Ensure that the housing covers or protective covers remain closed during operation!
ADVICE & THERMAL PROTECTION
This device is equipped with a ventilator regulated by the inside temperature. When the machine’s thermal pro-
tection is activated, it will not deliver any current. Orange light (Fig-V-2 / p.75) will turn on until the temperature
of the machine has returned to normal.
• Do not block/cover the ventillation holes, ensure free ow of air.
• Whilst in thermal protection mode leave the machine plugged into the mains after welding to allow it to cool.
General observations :
Always respect the basic rules of welding.
Always work in an adequately ventillated area.
• Do not work on a damp surface.
TROUBLESHOOTING
SYMPTOMS POSSIBLE CAUSES REMEDIES
The welding wire speed is
not constant.
Debris is blocking up the opening. Clean out the contact batch or change it
and replace the anti-adherence product.
Ref.041806.
The wire skids in the rollers. • Control the roller pressure or replace it.
• Wire diameter non-compatible with roller
• Covering wire guide in the torch
non-compatible.
The wire-feeder motor
doesn’t operate.
Reel or roller brake too tight. Release the brake and rollers.
Electrical supply problem. Check that the power switch is in the "On"
position.
Bad wire feeding. Covering wire guide dirty or damaged. Clean or replace
The drive roller is too loose Tighten the drive roller knob
Reel brake too tight Release the brake
No welding current Bad connection to the main supply. Check the mains connection and look
if the plug is fed by 230 V (1PH) power
socket.
Bad earth connection. Check the earth cable (connection and
clamp condition).
Torch trigger inoperative. Check the torch trigger / replace torch
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys EASYMIG 150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys EASYMIG 150 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info