665742
18
Verklein
Vergroot
Pagina terug
1/86
Pagina verder
EASYMIG 130 / 140 / 150
EN
18
SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)
Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/
recommendations printed on the side of the machine.
The Easymig 140 and 150 can be equipped to weld with aluminium wire Ø 0,8 or 1,0 (g II-B / p.74).
The Easy Mig 130 is delivered equipped for welding Aluminium of Ø 0.8mm (Occasional and non-intensive).
In this case the wire used should be stiff to facilitate wire feeding.
For use with aluminium, the gas requirement is pure argon (Ar). For the specic gas requirements please contact
your distributor. The gas ow in Aluminium is between 20 and 30 Litres/minute depending on the environment,
and the experience of the welder.
Below are the differences between welding with Steel and Aluminium :
- Specic rollers are needed for welding with Aluminium.
- Adjust the pressure of the drive rolls to prevent the wire being crushed.
- Only use a capilliary tube for welding with Steel or Stainless Steel.
- Use a special Aluminium Torch with a teon sheath to reduce friction.
DO NOT cut the sheath close to the joint, it is used to guide the wire from the the rollers.
- Contact Tube : Use a special aluminium contact tube specic to the diameter of wire being used.
GASLESS WIRE WELDING
Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/
recommendations printed on the side of the machine.
The Easymig can weld gasless wire up to 0.9mm, if the polarity is reversed (g III / p.75) respecting a maximum
pressure of 5Nm. For parameters of use, please refer to the instructions indicated on page 74. Welding gasless
wire with a standard nozzle can lead to overheating and deterioration of the torch. It is recommended to use a
“No Gas” nozzle (ref. 041868), or remove the genuine nozzle (Fig. III / p.75).
ELECTRODE WELDING
The reverse polarity cable must be disconnected in MMA (stick welding) mode in order to connect the electrode
holder and earth clamp. Connect the electrode holder and earth clamp as indicated on the electrode packaging.
• Respect the basic rules of welding.
• This device has 1 feature specic to Inverter machines :
- Anti-Sticking: Enables easy removal of the electrode from the metal. The anti-sticking feature, after its start,
requires approximately a 3 seconds delay before resuming normal welding operations.
SETTINGS PANEL (FIG V / P.75)
1
• Green light «ON»: when the machine is switched on the light
turns on.
• In case of power failure, the green light goes off but the device
remains powered while the power cable is unplugged.
2
• Orange light :
• Over-temperature: in such a case you shall wait a few minutes,
the light will turn off and the machine will start again.
• Over-current on primary circuit: in such a case you shall switch
off the machine (with the main switch) and switch on.
3
• Left button:
- MIG / MAG Welding : Adjust the wire feeder speed up to
maximum speed.
- MMA welding : Adjust the welding current.
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys EASYMIG 150 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys EASYMIG 150 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 4,11 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info