625733
8
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
8
BATIUM 25/24
CHARGING FUNCTION IUIO
This function enables to charge lead traction batteries for forklift truck, fork lift, industrial oor cleaning machine, with batteries from
35 Ah to 180 Ah. To connect the charger, process as below:
1. Directly on the battery, use the standard charger clamps
2. On the specic charger plug, replace the clamps at the cable end by the connector adapted to your machine. Respect the polarity
and the current scale.
Find below the charging process :
Voyant allumé Achage
Phase 1 :
Voltage rise
Charging
current
Phase 2 :
Voltage regulation (during 2 hours)
Charging
current
Phase 3 :
Charge end (Floating)
Nb: If the battery stays connected after the the end of the charge, each 72h, Batium 25/24 starts again a charging cycle
to keep the battery 100% charged.
FORCED CHARGE FUNCTION
In case of a deeply discharged battery, (Voltage under 2V), Batium remains in hold and displays:
. A chain of lights on the current screen
. The indicators « battery voltage », « capacity » and « charging curve » are on.
To force thecharge, press 5 seconds on the key (2) until Batium indicates CHE (=check). The charger detects a battery with a
voltage above 0.8 V.
As for the other models, this step is divided into 2 steps:
1. Diagnostic step (battery voltage analysis).
Nb : For 12v or 24 V batteries, during this step, as your battery is discharged, Batium will detect and offer you a 6V voltage. To
validate or adjust the voltage, press (2) (in less than 10 sec after the rst press). See anomaly 6.
2. Recovery step (voltage rise). This step may last up to 30 minutes max.
The diagnostic stage is over (CHE), Batium carries on with normal charge. For more information on the charging process, please
refer to the subdivision Charging function IUoU.
SOS RECOVERY FUNCTION
This function concerns all automotive batteries which are deeply discharged (IUoU).
After the battery has been plugged in, BATIUM does a diagnosis of the battery: Light signal « CHE » displayed.
If after 1 minute, the signal “SOS Recovery” ashes, this means the battery is sulfated.
The “SOS Recovery” function, thanks to a specic charge curve, starts a 24 hours recovery cycle.
To activate this function, proceed as following:
1. Disconnect the battery from the mains. (HIGH VOLTAGE RISK)
2. Connect the Batium to the outlet, then turn the device ON.
3. Select the IUoU charge curve.
4. Activate « SOS Recovery » by pressing during 5 seconds the «SOS recovery» key till the light (6) lights up.
5. Select the battery voltage and charging speed.
6. Connect the Batium’s clamps on the battery, the desulfation of the battery starts.
Indicators lit Displaying
Step 1:
Analyze, starting of the desulfatation and restoration of the
battery
Display of the current.
According to the battery behavior, the
current may increase or decrease.
Step 2 :
Desulfatation
Display of the current
Step 3 :
End of charge.
Battery irretrievable
Batterie saved
PROTECTIONS
The Batium is protected against short-circuits, polarity inversions and engine starts. It has an anti-spark feature which prevents sparks whilst
the battery is connected to the Batium. The Batium will not deliver current if there is no battery detected (no voltage in the clamps).
EN
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys BATIUM 25-24 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys BATIUM 25-24 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info