467111
332
Verklein
Vergroot
Pagina terug
1/345
Pagina verder
332 Programming examples - Helicopter models
helicopter follows the tail stick direction.
In the menu …
»Stick mode« (page 116)
Thr trim
Pitch/thr
Roll
Pitch ax
Tail rot.
Tr i m
0.0s
Tr. step – time +
global 0.0s
global 0.0s
global 0.0s
0.0s
0.0s
0.0s
0.0s
4
4
4
4
… the column "Tr. step" is used to set the increment
size of each "click" on the digital trim keys.
The C1 trimming only affects the throttle servo for the
helicopter. At this point there is no need to go into the
particulars of this trimming ("cut-off trim") once again.
(Thanks to digital trimming, trim values can be saved
automatically when a model change is affected. In
the mc-32 HoTT system these can even be stored
automatically when a change of flight phase takes
place.).
An additional setting which is specific to helicopters
can also be made in this menu in which you determine
which function the trim slider on the pitch stick should
have. This is accomplished by selecting the "Throttle
limit" setting in the "Throttle" line or leaving it as it is.
This roughly corresponds to trim for the familiar idle
trim function. If the trim indicator marker is moved all
the way forward by "turning" the trim wheel (remember:
"pitch min rear" = "throttle forward") the throttle limit will
later take over the throttle limit for throttle enable seam-
lessly in the menu …
»Control adjust« (page 122)
0%
I13 +100%
I14
I15
Tl16
Ty p
+100%
– travel + –time+
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
GL
GL
GL
fr
fr
Lv1
---
---
---
offset
GL
Normal
0.0 0.0
fr ---
SET
… where input "Tl16" is assigned and all other inputs
are "fr(ee)" by default.
This "Tl16" input serves as the throttle limiter. The
effect of a switch or a control assigned is exclusively
on output "6", where the throttle servo is connected.
The throttle limiter is assigned by default to the right-
side proportional rotary control.
In rmware versions up to and including
1102 the throttle limiter to the right side
proportional rotary slider SD1 is assigned
by default, as shown above. As of rmware
version 1103 is the input “Lim.” Default “free” and
consequently deactivates the throttle limiter
function. To enable this feature, only needs to
input “Lim.” Another donor, for example, the
original proportional rotary slider SD1, are
assigned.
Once again, as a reminder:
With the use of the "throttle limiter"
function, you do not have to program a
ight phase "throttle pre-selection".
The throttle limiter does not control the throttle
servo; it only limits the travel of the throttle servo
in the full throttle direction according to its position.
The throttle servo is generally controlled from
the pitch stick via »Helicopter mixer« menu
setting/s for throttle curve/s, which is why input 6
must absolutely remain "free". Refer to pages 194
in this manual about this.
The C1 trimming also affects only the throttle
servo for the helicopter. At this point there is no
need to go into the particulars of this trimming
once again. (Thanks to the digital trimming, trim
can be automatically saved values with a model
changeover as well as with a change of the ight
phase).
A detailed description of the idle run base setup
model and the adjustment of idle and throttle limit
can be found beginning on page 128.
Then switch to the "travel" column with the selec-
tion key of the left or right touch pad and increase
the now inversely highlighted value from +100 % to
+125 % with a fully opened throttle limiter with a brief
tap on the centre SET key of the right touch pad:
0%
I13 +100%
I14
I15
Tl16
Ty p
+100%
– travel + –time+
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
0%
+100%
0.0 0.0
GL
GL
GL
fr
fr
Lv1
---
---
---
offset
GL
Normal
0.0 0.0
fr ---
+125%
SET
In doing so, it is assured that the throttle limiter re-
leases the entire throttle travel with the pitch stick
later during flight.
Adjustment notice for electric helicopters:
Since electric drive systems have no need for
an idle setting, the basic conguration of
settings for an electrically-powered helicopter
merely involves making sure that the control range of
the throttle limiter is both higher and lower than the
adjustment range of the speed controller (usually
-100 % to +100 %) by a safe margin. If necessary,
therefore, the adjustment of the "travel" setting of the
throttle limiter described above must be modied
accordingly, for example, to symmetric +110 %. The
further adjustment, however, can take place
332

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Graupner-MC-32-HOTT

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Graupner MC 32 HOTT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Graupner MC 32 HOTT in de taal/talen: Engels als bijlage per email.

De handleiding is 46,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Graupner MC 32 HOTT

Graupner MC 32 HOTT Gebruiksaanwijzing - Nederlands - 328 pagina's

Graupner MC 32 HOTT Gebruiksaanwijzing - Deutsch - 320 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info