544625
4
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Please read first - then do programming!!!
Before programming your TCS-Cody with your personal codes, please check the faultless
function of the appliance with the help of the factory‘s pass code 1234 and the key-operated
pushbutton.
Normally, any programming is made via your personal master code. In order to get familiar
with that kind of programming, you start with the input of a new pass code, which replaces
the one preset by the factory (1234). The procedure is explained under item
“Program2“.
After that please change the master code to the string of digits you choose.
ATTENTION
In case you made a mistake on programming, you can start again by actuation of the key-
operated pushbutton (`*`).
Program 1
Input of a new master code
Assembly Instructions
Assembly of the CODY keyboard:
1. By slightly pushing the two latches at the right and left side of the keyboard
from behind to the edge, remove the small frame from the keyboard.
2. Now you see two fixingholes (diam. = 4 mm) at the front of the keyboard.
By means of these you can fix the keyboard onto the wall.
3. Connect the keyboard to the logic unit by means of a twin-cable (up to 5 m long).
There is no particular polarity for the twin wires.
4. Now re-fix the small frame.
5. It is possible to connect in parallel up to four keyboards if a thin connection cable, max.
total line cross-section 1.5 mm
2
, is used.
Keyboards connected in this way must not be operated simultaneously.
Assembly of the logic unit (inside area):
1. Put the screw-driver into the gap of the enclosure front, push the screw-driver up and
open the enclosure.
2. Remove the control PCB (which is force fitted to the inside of the enclosure).
3. Locate the screwed glands supplied (sealing nipple left side) in the
enclosure and replace the PCB. (Please ensure PCB is firmly in position)
4. Bore the fastening holes and fix the enclosure bracket at the wall.
5. The wires for the keyboard ensure through the left cable entry (sealing nipple), the wires
for the relay contacts through the three middle cable entries and the wires for the supply
voltage ensure through the right cable entry. Ensure tight seating of sealing nipple and
cable gland, otherwise the water-protection ot the appliance cannot be assured.
6. According to connection diagram connect the wires to the corresponding terminals.
Connections: Keyboard, UP - control, DOWN - control, STOP - control,
Supply voltage
Programming Instructions
Spannungs-
versorgung
Tastatur
Trafo
Industrietor
Antrieb
Netz 3x400 V
AB
AUF
STOP
Generalreset
X N L1 N PE PE
Connection diagram:
Input 8-digit
master code
Input 8-digit
NEW master code
Sound
signal
2 x long
Push key
button
Push key
button
Sound signal
1 x long
Sound signal
1 x short
Push key
button
The new master code is now stored !
1
Motor reversing by interchanging of connection wires UP (black) and DOWN (brown).
keyboard
GENERAL RESET
Push Button
power supply
power supply
400 V
Industrial door
drive
UP
DOWN
STOP
Trans-
former
industial controls
®
industial controls
®
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Geba Tronic TCS-Cody 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Geba Tronic TCS-Cody 3 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Geba Tronic TCS-Cody 3

Geba Tronic TCS-Cody 3 Gebruiksaanwijzing - Nederlands - 4 pagina's

Geba Tronic TCS-Cody 3 Gebruiksaanwijzing - Deutsch - 4 pagina's

Geba Tronic TCS-Cody 3 Gebruiksaanwijzing - Français - 4 pagina's

Geba Tronic TCS-Cody 3 Gebruiksaanwijzing - Espanõl - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info