813412
18
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
18
2.26 The Inlet Extension Pipe needs to be fitted in the correct
orientation, see Diagram 11.
11
90º End
Into Appliance
Short Section
Out of Appliance
2.27 From the rear of the appliance, feed the 90º angle of the
Inlet Extension Pipe through the hole in the back of the
Plinth or Bench, see Diagram 12.
12
Hole in rear of
Plinth or Bench
Inlet Pipe
Extension
2.28 Continue to feed the pipe through the hole, rotating so that
the 90º angle is upright and guide through the silicone
panel in the base of the firebox.
2.29 Remove the isolation elbow from the appliance and
connect to the Inlet Extension Pipe inside the firebox.
2.30 Connect the isolation elbow to the appliance gas inlet pipe.
13
Inlet Pipe
Compression Elbow
Inlet Pipe
Extension
2.31 At the rear of the appliance, fit the supplied 8mm elbow to
the Inlet Extension Pipe.
WARNING: THIS APPLIANCE IS HEAVY.
USE CAUTION WHEN INSTALLING, REMOVING
AND STORING AS THE APPLIANCE IS HEAVY AND
SHOULD BE HANDLED CAREFULLY.
AT LEAST TWO PEOPLE WILL BE REQUIRED TO
INSTALL THIS APPLIANCE.
2.15 Remove the securing spring clip from the bottom-right of the
window frame, see Diagram 9.
9
2.16 With the window frame in an upright position slide the frame
to the left so that it comes off the left hinge pin, see Diagram
10 (1).
2.17 Still keeping the frame upright drop the left side down and
forward slightly, see Diagram 10 (2).
10
1
2
2.18 Slide the frame to the right so it comes off the right hinge
pin. The window frame should now be free.
2.19 Refit the Window Frame Assembly in reverse order.
When closing the door ensure the door catches are fully
engaged.
UNDER NO CIRCUMSTANCES SHOULD THE
APPLIANCE BE USED WITHOUT THE CATCHES
HOLDING THE DOOR IN PLACE.
2.20 Remove the box from the appliance and store safely as it
contains the remote control and fuel effects, etc.
2.21 Remove all the enamel liners where necessary. The rear
panels on Studio 1 can remain in place, see Replacing
Parts, Section 5.
2.22 Remove the Main Burner, see Replacing Parts, Section 6.
2.23 Remove the Main Control Assembly, see Replacing Parts,
Section 7.
2.24 The gas supply enters the appliance through a silicone
panel in the base of the firebox.
2.25 Slit the silicone panel with a sharp knife.
Installation Instructions
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gazco Studio Freestanding Balanced Flue bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gazco Studio Freestanding Balanced Flue in de taal/talen: Engels als bijlage per email.

De handleiding is 8.63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info