Handleiding Gastroback 40977 (pagina 56 van 65) (Duits, Engels)

714637

Verklein

Vergroot

Pagina terug

1/65

Pagina verder

EN EN

110 111

REMOVING OBSTACLES

WARNING – Do not pour any type of liquid into the feed chute of the mincer,

while the mincer is assembled to the mixing arm. Do not insert any foreign objects

into the feed chute (e.g. cooking utensils). Do not remove the screw ring from the

mincer housing with the mincer assembled to the mixing arm and the machine con-

nected to the power supply.

CAUTION – Immediately switch off the motor (press the control dial), when the

motor keeps running noticeably slowly or gets blocked. This may avoid overloading

or overheating the motor and thus maintain long-lasting high performance of the motor.

When processing tough pieces of food (e.g. tendons or gristle within meat) or dough

with pieces of nuts, fruit, or hard vegetables and similar ingredients, the mincer may

be clogged. Large, hard pieces (e.g. bones) could block the worm shaft and/or

cross blade. In the extreme case, the mincer could get damaged (see: ‘Tips for Best

Results / Using the Mincer’).

1. Press the control dial for switching off the motor and unplug the machine.

2. Remove the tablet of the mincer. Then, remove the mincer from the mixing arm

and turn off the screw ring from the mincer housing (see: ‘After Usage / Remo-

ving and Disassembling the Mincer’).

3. With single hard pieces clogging the outlet of the mincer, it may be sufficient to

pull out the mincing disc, clean the holes of the mincing disc, and remove the

blockage from the cross blade. Check, whether the worm shaft can be turned

freely within the mincer housing. With the worm shaft blocked (you cannot turn

it manually after removing the screw ring), you must disassemble the mincer com-

pletely (see: ‘After Usage’). Possibly, you need to press the worm shaft and used

tools out of the mincer by pressing on the hexagonal shaft of the worm shaft.

4. Remove the obstacle and check, if the parts of the mincer are undamaged.

Damaged parts must be replaced. Ensure that the openings of the used tools are

free from obstacles.

5. Re-assemble the mincer according to the instructions for the individual tools (see

above).

IMPORTANT - Ensure that the hexagonal shaft of the worm shaft and the coupling

side of the mincer are completely clean and dry, before re-assembling the mincer

to the mixing arm of the machine. Otherwise the mincer coupling of the mixing

arm could be polluted or even get damaged.

6. If required, clean and dry the hexagonal shaft and the coupling side of the mincer.

7. Re-assemble the mincer at the mixing arm of the machine (see above). Ensure that the

motor of the machine is operating as usual, before processing further pieces of food.

NOTE

For further information refer to the chapter ‘Solving Problems’.

OPERATING TIME AND PAUSE FUNCTION

For your convenience, the machine offers an operating timer and pause function.

These features are described in this section.

ADJUSTING THE OPERATING TIME

You can set a pre-defined operating time. When starting motor operation, the set

operating time is counted down to zero and the operating time still required for com-

pleting the mixing process is shown on the operating time display.

When switching on the machine, the operating time starts always with the default

(20 minutes, “20:00”).

When turning the control dial back to zero speed (“00”), the operating time is set to

the default (20 minutes). If you wish to interrupt operation without resetting the timer,

use the pause function (see below: ‘Using the Pause Function’).

You can cancel operation at any time you like by turning the control dial to zero or

switching off the machine (pressing the control dial for approx. 2 seconds).

1. Press the up/down arrows at the left side of the operating time display for setting

the operating time. You may operate the machine using any value between 30

seconds (“00:30”) and 20 minutes (“20:00”) in steps of 30 seconds.

NOTE

Hold the appropriate arrow pressed, for scrolling through the timer setting auto-

matically.

2. After setting the operating time, turn the control dial clockwise for selecting the

desired speed and starting operation. The timer starts immediately and the ope-

rating time is counted down. When the timer reaches zero (“00:00”), the motor

is turned off automatically and zero flashes on the speed display (“00”). The

operating time is reset to the default value (20 minutes).

3. If you wish to cancel operation and/or set the operating time back to the default

value (“20:00”), simply turn the control dial back to zero (“00”) manually.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Gastroback 40977 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info