29053
10
Verklein
Vergroot
Pagina terug
1/78
Pagina verder
Airplane Section
FLAP-ELEVATOR
Mix (F-E)
This
function
is
used
to
compensate
for
trim
changes when flaps are deployed for show flight or
landing by mixing in a small movement of elevator.
The elevator should be adjusted to move only a
small deflection amount: too much elevator can
make the model difficult to control.
The amount of correction can be adjusted sepa-
rately for both positive and negative flap inputs,
and the neutral mixing position can be offset from
the flap neutral position. Flap-to-elevator mixing
can be turned on and off during flight by setting a
switch, but if an ON/OFF switch is not set, it
remains on all the time. The amount of mixing can
be changed by setting a volume control.
Setting Up Flap-to-Elevator Mixing
Activation of command
In the Condition Menu, press the
F-E
key to get the
FLP TO ELE menu shown below.
Mode setting
Offset amount setting
Mixing
rate
setting
U
ON/OFF switch
setting
Trimming volume
setting
Return to Condition
screen
Down side
Up side
Mode Selection Rate including volume adjustment
Use the A ( ) key to activate mode setting, then press
the ACT or INH
keys
(F and G)
to
activate
or
inhibit flap-to-elevator coupling.
Offset Position Setting
Use the B key to activate offset setting mode.
Then set the flap control to the offset position, and
press the SET key F to store the desired position in
memory.
Setting the Mixing Ratio Down and Up Side
You now set the amount of mixing for down flap com-
mand. Press the C key to activate mixing ratio for the
down direction and set the value with the numeric keys
E to M .
The number keys 0 through
100
input the
value directly. The + and - keys increase or decrease
the value by 1. The +/- key may be used to reverse the
throw direction. Your setting may vary from —100 to
+100%, the initial value is set to +50%.
Now set the amount of mixing for the up elevator
command. Press the D key to activate mixing ratio for
the Up direction and set the throw with the numeric keys
as before.
On/Off Switch Setting
Initially an activation switch for is not set, meaning
that once activated, this function is on all the time. If you
would like to set a switch to turn it on and off, call the
Switch Setting screen by pressing the
SWT P
key.
Then use the keys to choose the desired switch location
and on direction. For more information on the switch
setting method, see page 37.
Trim volume setting
You may set up the Flap-to-Elevator mixing so that its
effect may be changed in flight by moving a trim control.
The trim control allows you to adjust the volume within
±25% of the set mixing rate, which can be handy for
getting the best value while flying the model. This option
is not activated at initial setup.
Call the volume setting screen by pressing the VOL
O key, and select the desired control using the screen
menus (for a description of the volume setting method,
see page 37).
Use the
END
N key to leave this menu.
Airplane Section, Page 86
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 9ZHP_part2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 9ZHP_part2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info