29053
9
Verklein
Vergroot
Pagina terug
1/78
Pagina verder
Airplane Section
ELEVATOR- FLAP (E-F)
This mixing is used to droop the flaps whenever
an up elevator command is given (and may be set
up for down elevator as well, helpful during
'outside' maneuvers). It helps to eliminate 'buck-
ing,' and makes tight, square corners in maneuvers
for acrobatic aircraft.
Elevator-to-flap mixing can be set up to be
turned on and off during flight by a switch (if no
switch is activated, this mixing remains on all the
time).
You
can
also
set
the
flap
trim
rate
in
this
function. If the flaperon function is activated, the
elevators are mixed with the ailerons, otherwise,
the
mixing
is
with
the
flaps
only.
Setting Up Elevator-to-Flap Mixing
Activation of command
In the Condition Menu, press the
E->F
key to get the
ELE TO FPR menu shown below. Use the A key
to
activate
mode setting, then
press
the ACT or INH
keys ( F and G) to activate or inhibit Elevator-to-Flap.
ON/OFF switch
setting
Return to
Condition screen
Mode setting
Flap trim rate
Down side
Up side
Mixing
rate
setting
Mode Selection
Setting the Mixing Ratio — Down and Up Side
You now set the amount of mixing for down elevator
command. Press the C key to activate mixing ratio for
the Down direction and set the value with the numeric
keys E to
M
The number keys 0 through
100
input
the value directly. The + and - keys increase or de-
crease the value by 1. The +/- key may be used to
reverse the throw direction. Your setting may vary from
-100 to +100%, the initial value is set to +50%.
Now set the amount of mixing for the up elevator
command. Press the D key to activate mixing ratio for
the Up direction and set the throw with the numeric keys
as before.
Flap Trim Rate Setting
You may choose any value for the Flap Trim Rate.
Knob (A) is used to trim the position of the flap servo,
and the trim value controls the authority of the knob.
The authority may be set anywhere from 0% to 100%,
and the initial setting is 30%.
Call the flap trim setting screen by pressing the TRIM
RATE B key, and select the desired trim rate using the
screen menus. You may want a small number for this rate,
so that an accidental movement of the knob doesn't give a
large flap deflection.
On/Off Switch Setting
On initial setting, the activation switch for Elevator-to-
Flap mixing is set as SW (C) on at the upper position. If
you would like to change the switch or turn mixing on all
the time, call the Switch Setting screen by pressing the
SWT P
key. Then use the keys to choose the desired
switch location and on direction. For more information
on the switch setting method, see page 37).
Use the
END ( N )
key to leave this menu.
Airplane Section, Page 85
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Futaba 9ZHP_part2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Futaba 9ZHP_part2 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,43 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info