522136
41
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
34
4.6 Optional Water
Temperature/Speed
Sensor
Water temperature/speed sensor
ST-02MSB and ST-02PSB, which are
designed for thru-hull mounting, are
optionally available. Install them as shown
below.
Mounting considerations
Choose a suitable mounting location
considering the following:
Choose a place free from vibration.
Choose a mid-boat flat position. The
sensor does not have to be installed
perfectly perpendicular. The sensor must
not be damaged in dry-docking
operation.
Choose a place apart from equipment
generating heat.
Choose a place in the forward direction
viewing from the drain hole, to allow for
circulation of cooling water.
1. Dry-dock the boat.
2. Make a hole of approx. 51 mm diameter
in the mounting location.
3. Unfasten locknut and remove the
sensor section.
4. Apply high-grade sealant to the flange
of the sensor.
5. Pass the sensor casing through the
hole.
6. Face the notch on the sensor toward
boat’s bow and tighten the flange.
7. Set the sensor section to the sensor
casing and tighten the locknut.
8. Launch the boat and check for water
leakage around the sensor.
Locknut
Face "notch"
toward bow.
Flange Nut
Coat with
silicone sealant.
Brim
φ
77
51
123
Water temperature/speed sensor
ST-02MSB, ST-02PSB
4.7 Wiring
Refer to the interconnection diagram to
connect cables. Leave slack in cables to
facilitate checking and maintenance.
Establishing the ground
The ground wire (1.25sq or more, local
supply) should be as short as possible. The
ground for the signal line is isolated from
the chassis, however the power line is not
insulated. Therefore, to connect external
equipment whose positive polarity is
connected to the ground line, do not
connect the signal line ground to chassis
ground.
The signal line ground is isolated from the
chassis ground, however the power line is
not insulated. Therefore, when connecting
external equipment having positive ground,
do not ground the signal line to the chassis.
If excessive noise shows on the screen, the
ground may be inadequate. In this case,
attach a steel plate measuring 20 cm by 30
cm on the outside of the hull to provide a
ground point. Connect the ground wire
there. Use a “closed” type lug (
) to
make the connection at the display unit. Do
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
41

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno LS-6100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno LS-6100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info