522136
39
Verklein
Vergroot
Pagina terug
1/47
Pagina verder
32
If you do not know the transom angle,
temporarily attach the bracket and
sensor to the transom to determine if
the plastic shim is needed.
5. Using the two #10 x 1-1/4” self-tapping
screws, temporarily screw the bracket to
the hull. DO NOT tighten the screws
completely at this time. Follow the step
1-4 in “Attaching the Sensor to the
Bracket”, before proceeding with
“Adjusting”.
Adjusting
1. Using a straight edge, sight the
underside of the sensor relative to the
underside of the hull. The stern of the
sensor should be 1-3 mm (1/16-1/8”)
below the bow of the sensor or parallel
to the bottom of the hull.
11° transom angle
NO SHIM
12-18° transom angle
NO SHIM
2°-10°
transom
angle
19°-22°
transom
angle
shim with
taper up
shim with
taper down
parallelparallel parallel
slight
angle
angle
too steep
angle
reversed
YES NONO
YES YESYES
Sensor position and transom angle
Note: Do not position the bow of the
sensor lower than the stern because
aeration will occur.
2. To adjust the sensor’s angle relative to
the hull, use the tapered plastic shim
provided. If the bracket has been
temporarily fastened to the transom,
remove it, Key the shim in place on the
back of the bracket.
2°-10° transom angle (stepped
transom and jet boats): Position the
shim with the tapered end down.
19°-22° transom angle (small
aluminum and fiberglass boats):
Position the shim with the tapered end
up.
3. If the bracket has been temporarily
fastened to the transom, remove it.
Apply a marine sealant to the threads of
the two #10 x 1-1/4” self tapping screws
to prevent water seeping into the
transom. Screw the bracket to the hull.
Do not tighten the screws completely at
this time.
4. Repeat step 1 to ensure that the angle
of the sensor is correct.
Note: Do not position the sensor farther
into the water than necessary to avoid
increasing drag, spray, and water noise
and reducing boat speed.
5. Using the vertical adjustment space on
the bracket slots, slide the sensor up or
down to provide a projection of 3 mm
(1/8”). Tighten the screws.
Cable cover
Cable
clamp
50 mm (2")
Hull projection 3 mm (1/8")
Vertical adjustment and cable routing
www.Busse-Yachtshop.de email: info@busse-yachtshop.de
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Furuno LS-6100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Furuno LS-6100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,21 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info