780046
57
Verklein
Vergroot
Pagina terug
1/70
Pagina verder
Originalbetriebsanleitung Allgemein EN-57
29.5 Mounting the tyre and tube
1. Make sure that the rim tape covers the spoke nipples
and is undamaged.
2. Place the rim with one wall inside the tyre.
3. Push one side of the tyre completely into the rim.
4. Insert the valve through the valve hole in the rim and
insert the tube into the tyre.
5. Press the tyre over the edge of the rim.
6. Pull the tyre rmly into the centre of the rim.
7. The section that has already been mounted will slide
into the bottom of the rim.
8. Check that the tube is correctly positioned once again.
9. Used the ball of your hand to push the second half of
the tube completely over the rim ange.
10. For Dunlop or Blitz valves: Put the valve insert back
into its seating and tighten the union nut.
11. Inate the tube slightly.
12. Check the t and concentricity of the tyre using the
control ring on the rim ange. If it is not completely
round, correct the t of the tyre using your hand.
13. Inate the tube to the recommended tyre pressure
28. Tyres and tubes Page EN-53.
29.6 Installing the wheel
Please note that the work steps described here are
examples. Please follow the instructions of the respective
manufacturer, or get in touch with your dealer.
29.6.1 Inserting the front wheel
Warnings
Seriousfallsandaccidentscausedbyinsucient
bicycle control.
Pay attention to the direction of rotation of the tyre
when installing the front wheel.
If your bicycle has a disc brake, ensure that the
brake discs sit properly between the brake pads.
29.6.1.1 Axle nut: inserting the front wheel
1. Insert the wheel into the fork drop-out.
2. Tighten the axle nuts clockwise to the specied
tightening torque using a torque wrench 13.
Tightening torques for threaded connections Page EN-19.
29.6.1.2 Quick-release skewer: inserting
the front wheel
1. Insert the wheel into the fork drop-out.
2. Turn the clamping nut on the quick-release skewer
clockwise slightly.
3. Close the tensioning lever by folding it 180˚. The lever
should be very easy to move from the beginning of
the closing movement up to halfway. Then, the force
required to move the lever must signicantly increase
until the lever is very dicult to move at the end.
4. a) If the quick-release skewer closes too easily, the
pre-tension must be increased: Hold the tensioning
lever and turn the clamping nut on the opposite side
clockwise. Check whether the correct pre-tensioning
has been achieved by closing the tensioning lever.
b) If the quick-release skewer is too dicult to close,
the pre-tension must be reduced: Hold the tensioning
lever and turn the clamping nut on the opposite
side counterclockwise. Check whether the correct
pre-tensioning has been achieved by closing the
tensioning lever.
5. Close the tensioning lever. The lever must be
positioned in such a way that it cannot be opened
accidentally.
29.6.1.3 Inserting the front wheel through-
axle
1. Moisten the through-axle with a thin layer of grease.
2. Slide the wheel between the drop-outs.
3. Mount the through-axle 27.2.1 Mounting a R.A.T.
through-axle Page EN-52.
29.6.2 Inserting the rear wheel
29.6.2.1 Derailleur: inserting the rear wheel
1. When installing the rear wheel, position the chain on
the smallest sprocket.
2. Insert the wheel centrally in the drop-outs as far as it
will go.
3. Tighten the hub nut or close the quick-release skewer
27.1 Fastening wheels with quick-release skewers
Page EN-51.
29.6.2.2 Hub gear: inserting the rear wheel
I. Mounting a wheel with a gear hub in the frame
1. Place the chain on the sprocket and attach the hub
axle to the drop-outs.
CJ-NX10
JAPAN
Hub axle
Drop-out
Fig. 133 Inserting the rear wheel ©Shimano
2. Attach the locking washers to both sides of the hub
axle. Turn the shift arm so that the protrusions on the
locking washers engage in the drop-out slots. In this
case, the shift arm can be mounted almost parallel
to the frame fork. The protruding part must be on the
side of the drop-out. Insert the locking washers so that
the protrusions engage exactly in the drop-out slots on
the front or rear of the hub axle.
57

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Focus 2021 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Focus 2021 in de taal/talen: Engels als bijlage per email.

De handleiding is 5.36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Focus 2021

Focus 2021 Gebruiksaanwijzing - Nederlands - 71 pagina's

Focus 2021 Gebruiksaanwijzing - Deutsch - 72 pagina's

Focus 2021 Gebruiksaanwijzing - Français - 74 pagina's

Focus 2021 Gebruiksaanwijzing - Italiano - 71 pagina's

Focus 2021 Gebruiksaanwijzing - Espanõl - 72 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info