775826
74
Verklein
Vergroot
Pagina terug
1/98
Pagina verder
190 Series III
Users Manual
68
Voltage Modulation
Use voltage modulation to display the modulated output signal.The submenu has selection for
what reference is used for the measurement.
Phase-Phase
Phase-Phase shows the modulated signal between 2 phases. The PWM voltage, voltage peak-
peak, frequency, and volt/frequency ratio show as readings in the top of the display. PWM voltage
shows on the display but not the rms voltage. PWM voltage represents the effective voltage of
the switching output based on the average value of samples over a whole number of periods of
the fundamental frequency.
2 adjusts the zoom level (1, 2, or 3) of the waveform as well as the corresponding
readings.
For Zoom 2, the test tool selects a time base that shows the pulses in more detail and the
readings change to Volt Peak Max, Volt Peak Min, and delta voltage between the upper and
lower levels.
4 BURST (positive or negative) selects either the positive part of the modulated signal or
the negative part of the modulated signal. This selection also applies when you change to
Zoom 3.
For Zoom 3, the test tool selects a time base that shows the edge of pulse of the modulation
signal. A pulse with a high peak is selected automatically to find the highest dV/dt value.
The readings change to Volt Peak Max, dV/dt, risetime, and overshoot percentage when Peak is
selected as Risetime with 4. The risetime measurement is based on the IEC 60034-17
method that uses the 10 % and 90 % values of the peak of pulse. This peak value is used as dt in
the dV/dt reading and the Peak Voltage as dV. Make sure that the slope that is automatically
selected is indeed the pulse of the PWM signal and not of an interference. The start of the slope
must be around the 0-level.
4 LEVEL selects the readings for Delta Voltage, dV/dt, risetime, and overshoot
percentage. The risetime measurement is based on the NEMA MG1 Part 30.1 method that uses
the 10 % and 90 % values of the voltage level. This value is used as dt in the dV/dt reading and
the level voltage as dV.
To change the view of the waveform manually in any of the Zoom modes:
1. Push L or N.
2. To change the time base, use the V key.
3. Use the voltage, time, and dV/dt reading to see if the steepness of the switching impulses is
within the motor insulation specification.
74

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 190-102-III bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 190-102-III in de taal/talen: Engels als bijlage per email.

De handleiding is 9.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info