775826
73
Verklein
Vergroot
Pagina terug
1/98
Pagina verder
ScopeMeter® Test Tool
MDA-550-III Test Tool
67
Motor Drive Output
The Motor Drive Output functions check the drive output conditions. The modulated output
voltage varies with the motor speed and load. The output current depends on load and correct
function of the motor. Unbalance between the phases can cause or indicate problems. The stress
on the motor insulation can be determined by measurement of the risetime of a fast modulation
pulse.
Voltage and Current (Filtered)
Voltage and Current (Filtered) are measurements of the voltage, current, and frequency at one of
the phases of the motor drive output. The measurement is done with a 10 kHz bandwidth filter so
that a sinewave shaped voltage waveform shows instead of the pulse width modulated signal.
The voltage measurement is done between two phases (Phase-Phase). The current
measurement is done on a single phase. Repeat the measurement for the other phases.
The display shows the voltage waveform in red and the current waveform in blue. The PWM
voltage, rms current, frequency, and Volt/Hz factor (ratio between voltage and frequency) show
as readings at the top of the display. The PWM voltage shows and not the rms voltage, as PWM
voltage represents the effective voltage of the switching output based on the average value of
samples over a whole number of periods of the fundamental frequency.
2 changes the readings on the display to Volt Peak readings or Current Peak readings:
Peak-Peak, Maximum Peak, Minimum Peak, and Crest Factor (ratio between peak and RMS
value).
Tips:
Use the V/Hz ratio to check if the ratio is within specified limits for the motor.
If V/Hz is too high the motor will overheat and if V/Hz is too low the motor will lose torque.
Note
The peak voltage readings here are the peak of the effective voltage and not the peaks of
the actual PWM voltage. Use the Voltage Modulation function to measure PWM voltage.
The Voltage and Current (filtered) function detects motor overloading. Stable Hz with unstable
V readings points to dc bus problems. Unstable Hz with stable V readings points to IGBT
problems. Unstable Hz and unstable V readings points to speed control circuits.
Check the output voltage on the motor drive with the nameplate rating. The current must be
within the specified Full Load Amps for the motor. Consider the motor service factor that
specifies the percentage of overloading the motor can handle for short periods of time.
If the output current is too high, the motor can run hot. A 10-degree temperature rise can
equal 50 % decrease in stator insulation life.
73

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fluke 190-102-III bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fluke 190-102-III in de taal/talen: Engels als bijlage per email.

De handleiding is 9.23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info