778615
18
Verklein
Vergroot
Pagina terug
1/111
Pagina verder
[1-9] Gear switch
[1-10] Rotational direction switch and safety
lock/transport lock
[1-11] Handle
[1-12] Thumbwheel for torque/drilling/light
ing duration on and duration off
[1-13] Belt clip
[1-14] Bit store
[1-15] Insulated gripping surfaces (grey
shaded area)
Accessories shown or described are not always
included in the scope of delivery.
The specified illustrations appear at the begin
ning of the Operating Instructions.
6 Battery pack
Before using the battery pack, check that the
battery interface is clean. Any contamination of
the battery interface may impair correct contact
and lead to the contacts being damaged.
A faulty contact may result in the machine over
heating or being damaged.
[2A] Remove the battery pack.
[2B]
klick
Insert the battery pack – until it
clicks into place.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
7 Commissioning
CAUTION
Risk of injury
Only assemble when the power tool is
switched off!
7.1 Belt clip [1-13]
The belt clip allows the power tool to be attach
ed to work attire for brief periods. It can be at
tached to the right or left of the power tool us
ing a screw [3].
7.2 Fitting the auxiliary handle [5]
WARNING! Always use the auxiliary handle.
Check that the auxiliary handle [5-1] is se
curely in place.
7.3 Inserting the stop bar [6]
The drilling depth can be adjusted using the
stop bar [6-1].
7.4 Switching on/off [1-5]
Press = ON, release = OFF
The speed can be continuously adjusted,
relative to the pressure applied to the
on/off switch.
Set the rotational direction switch [1-10] to the
centre position to lock the on/off switch.
The LED light [1-4] lights up when the on/off
switch [1-5] is pressed, see section 8.4.
8 Settings
CAUTION
Risk of injury
Only adjust the settings when the power
tool is switched off.
8.1 Changing direction of rotation [1-10]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
8.2 Changing gear
The gear switch [1-9] can be used to switch the
gear unit when the power tool is switched off.
8.3 Adjusting the torque [1-12]
Screwdriving
Torque corresponding to setting at the thumb
wheel [1-12]:
Position 1 = low torque
Position 13 = high torque
There is a signal when the set torque is
reached and the power tool switches off. The
power tool only starts up again if the on/off
switch [1-5] is released and pressed again.
Drilling
Marking shows the drill symbol = maxi
mum torque.
8.4 Adjust lighting [1-12]
Configure lighting at the thumbwheel [1-12].
Marking shows position 1 to 13 or drill sym
bol . The LED light [1-4] automatically
switches on and off with the power tool. The
LED light has an afterglow for a short time after
the tool has been switched off.
English
18
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool TPC 18-4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool TPC 18-4 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3.53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info