497992
17
Verklein
Vergroot
Pagina terug
1/107
Pagina verder
C A R V E X
17
GB
In position
A
, the automatic load detection is
activated: The stroke speed is reduced in
idling and is controlled to the highest value
when the blade enters the workpiece.
8 Working with the machine
When working on small or thin workpieces, al-
ways use a stable base, or the CMS module
(accessory).
When working, hold the electric power tool by
the handle and guide it along the desired cut-
ting line. For precise cuts and smooth running,
use two hands to guide the electric power tool.
Free saw guidance along a scribe mark
The triangular pointer on the splinterguard
[4-1]
indicates the cutting line of the saw
blade. This facilitates sawing along a scribe
mark.
8.1 Lighting
A continuous light or stroboscope is installed
for illuminating the cutting line:
up to approx. 2100 rpm: continuous light
from approx. 2100 rpm: stroboscope light
L
In overhead position (+/- 45°), the lighting
is switched off completely.
If required, you can adjust the lighting:
X
Plug in the electric power tool.
X
Press both buttons simultaneously
[1-2]
and hold for approx. 10 s until a beep
sounds.
X
Release both buttons
[1-2]
.
X
Press the left button (on the pendulum
stroke side) to select the stroke speed and
consequently the desired operating mode:
X
Press the right button to save the setting.
9 Service and maintenance
Customer service and repair
only through manufacturer or ser-
vice workshops: Please find the
nearest address at:
www.festool.com/Service
Use only original Festool spare
parts! Order No. at:
www.festool.com/Service
Damaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop, unless otherwise indicat-
ed in the operating manual.
Recommended stroke speed (position
of the adjusting wheel)
Hard and soft wood, plywood board,
plywood, chip board
A
Hardboard 4 - A
Plastic 3 - A
Ceramic, aluminium, non-ferrous
metals
3 - 5
Steel 2 - 4
CAUTION
Material with high dust generation (e.g.
plasterboard)
Damage to machine through dust pene-
tration, risk of injury
X
Do not work overhead!
WARNING
The stroboscope light may make it diffi-
cult to determine the saw blade posi-
tion
Risk of injury
X
Ensure the work area is well illuminated.
Mode Indication
during config-
uration
Behaviour dur-
ing operation
1 Light flashes With strobo-
scope (standard)
2 Light on Permanent light
without strobo-
scope
3 Light off Light switched off
WARNING
Risk of injury, electric shock
X
Always disconnect the mains plug from the
socket before performing maintenance
work on the machine!
X
All maintenance and repair work which re-
quires the motor housing to be opened
must only be carried out by an authorised
service workshop.
EKAT
1
2
3
5
4
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool PS CARVEX 420 EBQ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool PS CARVEX 420 EBQ in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 7,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info