778630
23
Verklein
Vergroot
Pagina terug
1/142
Pagina verder
ing cut, the motor is switched off immediately.
To put the power tool back into operation, it
must first be switched off and then on again.
Restart protection
The built-in restart protection prevents the
power tool from starting up again automatically
if the power is disconnected during continuous
use. To put the power tool back into operation,
it must first be switched off and then on again.
Overheating protection
In the event of overheating, the safety electron
ics system switches to cooling mode. The motor
continues to run and the constant speed is de
activated. Let the machine cool down for ap
proximately 10–20 seconds before using it
and/or fully loading it again.
6 Commissioning
The dust extraction attachment is preassem
bled and must not be removed or repositioned.
6.1 Holding the power tool correctly
Hold the power tool with both hands using the
insulated gripping surfaces [1-8]: One hand on
the motor housing behind the switch and the
other on the auxiliary handle [1-3].
6.2 Switch on/off
Switching on [2a]
Push the on/off switch [1-4] forwards.
Pressing the front part of the switch at the
same time locks the on/off switch.
On/off switch [1-4] is locked and the power tool
is switched on.
Only position the tool on the material once
it has reached operating speed.
Setting the speed
The speed can be adapted in six settings de
pending on the workpiece requirements.
Set the speed regulator [1-7] to the re
quired setting.
Switching off [2b]
Lift the power tool from the processed ma
terial.
Press the rear part of the on/off
switch [1-4].
Lock is released and the power tool is switched
off.
WARNING
Risk of injury from kickback, ejected parts
Before setting down the power tool, wait
until the rotating sanding tool has come to
a complete stop.
Set the power tool down flat on the dust ex
traction attachment.
7 Battery pack
Inserting the battery pack [3a]
Removing the battery pack [3b]
7.1 Capacity display
The capacity display [1-12] indicates the charge
of the battery pack for approx. 2 seconds after
the button [1-11] is pressed:
70‑100%
40‑70%
15‑40%
< 15% *
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
8.1 Fitting the auxiliary handle [1-3]
Always use the auxiliary handle to ensure
a safe working posture that prevents you
from tiring.
The special "VIBRASTOP" design of the auxiliary
handle helps to reduce vibrations.
Screw in the auxiliary handle [1-3] on the
side of the thread [1-2] according to the
working method.
English
23
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Festool DSC-AGC 18 FH bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Festool DSC-AGC 18 FH in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3.55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info