510132
7
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
EN
7
To prevent the workpiece or your fingers
from getting caught between the work plate
(12) and the sanding disc (11), the space
between work plate (12) and sanding disc
(11) must not exceed 1.6 mm.
The choice of sanding paper
With coarse sanding paper (P 60) generally most
of the material can be removed, and fine sanding
paper (P 150) is then used for finishing. An
uneven surface is first treated with coarse sanding
paper and sanded until it is even. Subsequently
medium-coarse sanding paper (P 100) is used to
remove the scratches caused by the first type of
paper used. Fine sanding paper (P 150) is used
for finishing. The sanding needs to be continued
until the surface is smooth.
The placing of the sanding paper
Fig. 6 - 9
When the sanding machine is held with the
sanding disc turned towards you, the sanding
belt moves from right to left along the upper part
of the machine. Because of this turning direction
the workpiece will be pressed against the right
side of the fence. An arrow on the inside indicates
the right direction of running of the sanding belt
(see drawing). If no direction is indicated, the
sanding belt must be placed in such a way that
the elevated part of the seam is placed into the
turning direction of the belt. So it is very important
that the sanding belt is placed in the correct
way. The machine uses standard 100 x 915 mm
sanding belts (nr 7):
• Remove the plug from the mains socket.
• Push the clamping handle completely to the
right to take away the tension of the transport
rollers (Fig.1: 14).
• Push the sanding belt along both of the
transport rollers, starting from the back of the
machine.
• Push the clamping handle completely to the
left. Now the sanding belt should be
completely tight.
• Turn the transport roller exactly in a right angle
to the direction of the sanding belts with the
use of the winged nut at the right roller. The
direction of running of the belt is adjusted
correctly if the sides of the sanding belt are
running parallel to the bearing plate.
The sanding disc
Paper or “velcro” plates are used for the sanding
disc. The standard diameter is 150 mm. The
plates are self adhesive.
Vertical placing of the sanding belt
For more flexibility of the sanding belt its bottom
side can be used, because there is no bearing
plate. For an easy reach of this bottom side the
sanding belt can be placed in vertical position.
• Loosen the two nuts at the front of the sanding
machine, around the left transport roller shaft,
with the use of an open-end spanner.
• Push the sanding belt up in the position
desired.
• Fasten the two nuts again.
• The workpiece can now rest on the worktop
instead of on the sanding belt;
• The work plate which is used for the sanding
disc can now be pushed with the shaft into the
hole of the machine frame, at the left side of
the sanding machine.
• Fasten the bolt at the back of the machine.
• The work plate can now be used as support
for the sanding of the work piece against the
sanding belt.
4. Putting the machine into operation
Switching On/Off
• Press the switch into position ‘1’ to put your
sanding machine into operation.
• To switch off the machine the same switch
needs to be pressed to position ‘0’.
• Always keep the mains cable away from
moving parts.
• There is no need to apply any pressure with
the workpiece, because this only slows down
the speed of the sanding disc.
Sanding
The sanding belt and disc supplied with this
sanding machine are suitable for the sanding of
metal, wood or synthetic surfaces. The workpiece
should always be held firmly during sanding. No
extra pressure is needed. Guide the work piece
up and down over the sanding belt, in order to
prevent the sanding belt and plate from wearing
through in one place. Round objects can be
sanded at the ends of the sanding belt. Work
pieces which are longer than the sanding machine
can be sanded by removing the fence.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm BGM1003 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm BGM1003 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info