510132
6
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
EN
6
Wear ear and eye protection
wear a dustmask
Keep bystanders away
Special safety instructions
• The following points need to be checked:
• Do the connecting voltage of the machine
correspond with the mains voltage.
• Are the mains lead and the mains plug in a
good condition; strong, without ravels or
damages.
• For functional reasons the turning parts of this
machine are not covered. Therefore it is of
utmost importance to be careful. Hold the
workpiece firmly, to prevent it from slipping
from your hands. Never touch the sanding
surfaces of a working machine with your
hands.
• Avoid the use of long extension cables.
• If necessary, secure the sanding machine with
screws.
Before you operate the machine:
• Always keep the mains cable away from
moving parts of the machine.
• Use safety goggles.
• Use a dust mask.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
Immediately switch off the machine when:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or
mains lead damage.
• Defect switch
• Smoke or stench of scorched isolation
3. Before putting the machine
into operation
Installation
Avoid the use of long extension cables. If
necessary, secure the sanding machine on a
working bench with help of screws through the
holes in the feet of the machine frame. Do not
forget to leave enough space around the machine
for the workpieces to be sanded.
Assembly
• Put the machine frame on its head and press
the four rubber stops into the foot of the frame.
• Machine frame, aluminium disc (10) and work
plate (12) are supplied in separate packaging.
• Push the aluminium disc on the shaft and
fasten the disc with the socket bolt in the side
of the disc (Fig.2 - 4).
• Place the work plate (12) with the shaft in the
machine frame and secure the work plate with
the bolt in the side of the machine frame.
Check with a 90° sash angle on the work plate
and against the sanding disc if the angle is
exactly 90° (Fig.5).
• If necessary, adjust this angle with the
calibration indicator.
• The mitre scale (13), which is also supplied
separately, can be placed on the work plate
(12). With the use of this mitre scale the angle
of grinding can be determined precisely.
• The fence (8) for the belt sander can be placed
behind the uppermost bolt of the V-belt guard.
In this way the workpiece can be held firmly
against the belt, without great hazards.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm BGM1003 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm BGM1003 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 2,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info