764206
7
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
7
EN
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions. Keep these
instructions in a safe place!
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Prior to mounting an accessory always
unplug the tool.
Removing and mounting the guard
Fig. 2
Replace the guard only with one of sheet steel or
material of equal strength.
Disassembly
• Removetheflangenutandtheflangefromthe
spindle (2).
• Removethemachine’sprotectivehood.
Assembly
• Puttheprotectivehood(1)onthemachine.
• Turntheprotectivehoodtotheposition
indicated in the drawing and completely
tighten the screws (3).
• Puttheflangenutandtheflangebackonthe
spindle (2).
Mounting a grinding disc
Fig. 3
Use grinding discs of the correct dimension. Use
fibre reinforced grinding discs only. The grinding
disc must not touch the edge of the guard.
• Pressthespindlelock(6)andturnthespindle
(9) until it engages in the lock. Keep the spindle
lock pressed during this procedure.
• Removetheflangenut(12)fromthespindle
using the spanner (11).
• Positionthegrindingdisc(7)ontheflange(5).
• Placetheflangenutonthespindleantightenit
using the spanner.
• Releasethespindlelockandcheckthatthe
spindle is unlocked by rotating it.
Mounting the side handle
Fig. 1
The side handle can be used for both left-hand
and right-hand control.
• Fastenthesidehandle(5)forleft-hand
operation on the right-hand side of the
machine.
• Fastenthesidehandleforright-handoperation
on the left-hand side of the machine.
• Fastenthesidehandleforuprightworkingat
the top of the machine.
Make sure that the side handle is
fastened properly and cannot loosen
unexpectedly.
Mounting grinding discs and roughing discs
Fig. 4 and 5 show how to mount the flange (10)
when using thick (4 - 8 mm) and thin (2,5 - 4 mm)
discs.
4. USE
Always observe the safety instructions
and applicable regulations.
Special attention when starting the machine
• Clamptheworkpieceandmakesurethat
the workpiece cannot slide from under the
machine during the cutting activities.
• Whenworkingwiththemachine,alwaysholdit
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ferm AGM1081 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ferm AGM1081 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 14,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info