502531
7
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
THERMAL RE-SET
The machine is supplied with a thermal re-set switch. The switch will activate
when the machine becomes too hot. This condition should not occur during
normal use. To re-set the switch:
Isolate the machine from the mains supply.
Safely support the machine - to access the underside.
Using a cross-head screwdriver, open the cover plate.
Using a suitable tool, insert the tool through the aperture and press the
metal switch until it snaps closed. The switch will close correctly, only if the
machine is cool enough.
Replace the cover plate and screws.
Power-on the machine.
TROUBLESHOOTING
Problem Possible cause Solution
No power on LED Machine is not switched on Switch on machine at rear next to plug inlet and at the wall socket
Ready light does not come on after a
long period
Machine is in a hot or humid area Move the machine to a cooler and dry area
Pouch does not completely seal the item
Item may be too thick to laminate Pass through the machine again
Temperature setting may be incorrect Check pouch thickness is correctly selected and pass through again
Pouch has waves or bubbles Temperature setting may be incorrect Check pouch thickness is correctly selected and pass through again
Pouch is lost in the machine Pouch is jammed
Select reverse button and pull out the item by hand. Check cooling
plate is correctly positioned.
Jamming
Pouch was used ‘open end’ first
Pouch was not centred on entry
Pouch was not straight upon entry
Empty pouch was used
Cooling plate not fixed correctly
Pouch is damaged after lamination Damaged rollers or adhesive on rollers Pass cleaning sheets through the machine to test and clean rollers
Temperature not increasing
Main fuse failure
Check and replace
Power cord not fitted correctly
Curled or burnt laminations Too hot Reduce temperature or increase speed
Soft or poor lamination Too cold Increase temperature or reduce speed
Rollers not running
Rollers too cold (< 60°c) Wait for rollers to warm-up
"STOP" button may be pressed Press "MOTOR" or "SPEED" button
Unstable lamination temperature Roller electric brush may be broken
Contact service engineer
Cannot select any Mode Circuit board error
Rollers not running & motor is running Loose circuit bolts on gear
Excessive noise Gears word or damaged
Master fuse keeps failing Damaged circuit board
7
405600_EUR_Proteus_All_v1.5.indd 7 12/23/2010 1:50:33 PM
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Fellowes Proteus laminator bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Fellowes Proteus laminator in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info