502511
12
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
6.11 IMPROPER USE
The functions and use of this tool are those exclusively
indicated in this manual. Never use the tool to cut thick
tree trunks or branches.
Any other use of the tool is explicitly forbidden.
-Never cut aluminium or steel on the upper table.
-Always use sharp blades appropriate to the type
of cuts to be made.
-Never use the machine without the protective
devices described.
-Never use the machine for food-processing
purposes.
-Use only the right types of blade (see Table, Point
6.1) for the material to be cut: wood, aluminium
sections, PVC pipe, etc.
The cutting of any other type of material not
specied in this manual is expressly prohibited.
The machine comes with a brush that conveys
all dust into the suction area in order to limit the
quantity of dust generated during cutting.
WARNING! Whenever wood is cut, connection to an
external vacuum unit must be used in order to lower
the risk of exposure to dust.
Always wear dust-proof face masks.
7 MAINTENANCE
WARNING - Always unplug the plug from the power
supply socket before performing.
maintenan
Note: operating noise can be decreased by
using the right blades and performing frequent
maintenance on the blade and mitre saw itself.
7.1 LUBRICATION
The mitre saw is delivered already completely
lubricated and does not require any further lubrication.
7.2 ROUTINE CLEANING
WARNING - Avoid touching the handgrip with hands
that are dirty with oil or grease, and immediately
clean the handgrip whenever this happens.
- Clean the machine carefully after use by spraying
with compressed dry air.
WARNING - An attachment that can be easily
connected to any Felisatti vacuum unit is provide to
improve work conditions.
7.3 CHECKING THE DRIVE BELT
These machines are equipped with drive belts.
The right tightness of these belts is essential to
good operation and must be checked regularly and
adjusted whenever necessary by proceeding as
follows:
- remove the casing over the belt A (g.16) and
loosen the 4 screws C (g. 17) that keep the motor
unit in place.
- adjust the tightness of the belt using the
corresponding dowel B (g. 17).
- tighten the 4 screws C (g. 17) in order to lock the
motor unit in place and reassemble the protective
casing ove the belt.
WARNING! The failure to perform this operation
regularly may result in damage to the belt and
incorrect machine operation.
7.4 DISPOSAL
At the end of the machine working life, or
when it can no longer be repaired, ensure
that it is disposed of according to the standard
regulations of the country in which it is being used,
and that the disposal operation is carried out by
specialised personnel following authorised guidelines.
In all circumstances:
- Do not abandon in the environment;
- Do not dispose of together with solid urban
waste products;
- Contact the special recycling centers
8 PART REPLACEMENT
WARNING! - Always unplug the plug from
the power supply socket before replacing
spare parts.
8.1 BLADE REPLACEMENT (g. 18)
Proceed as follows to replace the blade:
Raise the upper table to its highest permissible height
- Release the movable protective casing L (g. 1) by
using the button B and raise it completely - Using the
two Allen wrenches supplied (on the blade side and
on the motor side) unscrew the screw C clockwise -
Remove the locking ange D, remove the blade by
rst sliding it to the left and then sliding it downwards -
Mount the new blade after making sure that the teeth
face the direction indicated by the arrow and then lock
it in place by screwing the screw C counter-clockwise
tightly down - Lower the movable protective casing L
by returning button B to its original position and then
make sure that the blade is protected when the blade
unit is completely raised.
WARNING! - Use only the blades recommended by
the Manufacturer and in compliance with Standard
EN 847-1. Make sure that the speed marked on the
blade is greater than the tool rated speed.
WARNING! - NEVER USE STEEL BLADES FOR
HIGH SPEEDS.
8.2 REPLACING THE POWER SUPPLY CABLE
Make sure that the power supply cable is in good
condition; if worn, have it replaced by an authorised
Assistance center.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Felisatti NTF250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Felisatti NTF250 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info