502511
11
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
WIDIA BLADES MATERIAL BLADE Ø – No. TEETH /min
WOOD
Ø 250 mm - Z 24 4500
Ø 250 mm - Z 40 4500
Ø 250 mm - Z 60 4500
Ø 305 mm - Z 72 4000
PVC Ø 250 mm - Z 60 4500
ALUMINIUM
Ø 250 mm - Z 60 4500
Ø 305 mm - Z 72 4000
FRAMES Ø 250 mm - Z 80 4500
does not provide shorter cutting times and can lead
to diminished efciency caused by the overloading of
the motor.
6.4.1 STARTING AND STOPPING THE BLADE
- Start the blade by pressing the tool lever A (g. 2)
and then wait until the blade reaches its maximum
rpm. - Lower the blade unit gradually and then
make the cut desired. After the cut has been made,
release the lever A (g. 2) and then wait until the
blade has come to a complete stop.
WARNING - Make sure that the movable protective
casings are all in correct position whenever the blade
is raised in rest position. The machine is provided
with a release button for the starting and stopping
of the blade. This button can be locked in “ON” by
pressing the switch black key B when the switch
black lever A is at the end of its stroke and the motor
is running (g. 2).
WARNING - This Lock in ”ON” button disables the
safety provided by the Manufacturer in the starting
lever switch. We recommend using this device only
with the greatest caution and only when the tool is
being used as a disk saw. In order to release the
switch, press the black lever A and then release it.
6.5 USING THE STROKE END RODS (g. 7)
Proceed as follows to use the stroke end rods: - Insert
the rod A in the hole of the workpiece support and lock
it in place with the corresponding knob B – Loosen
the knob C and adjust the rod D as required by the
length of the workpieces by using the millimetre ruler
for reference. Then lock the knob C back into position.
6.6 USING THE CLAMP (g. 8)
Proceed as follows to use the clamp:
- Insert the pin A in the corresponding slot B and lock
it in place with the dowel C located in the rear part of
the workpiece support
– Insert the clamp D on the pin A and lock it in place
at the desired height using the wing nut E
– Lock the piece to be cut into place by tightening
the upper knob F.
6.7 USING THE UPPER TABLE AS A DISK SAW
WARNING - The use of the upper table for the cutting
of steel and aluminium is absolutely prohibited.
- Never use the tool to make slots.
Proceed as follows to use the upper table: - Make
sure that the switch is not locked in “ON” - Completely
lower the blade unit and lock it in place using the pin
F (g. 1)
(RI and NTF305 version)
This version is equipped with ne-adjustment:
adjust the height of the upper table using the knob N
(g. 1) and then lock the table in position by tightening
the knob S (g. 1).
(RP version)
- Adjust the height of the upper table as required by
the piece to be cut, and then lock in position using the
corresponding knobs S (g. 1) and T (g.9).
6.7.1 STARTING AND STOPPING THE BLADE
- Start the blade by pressing the tool lever A (g. 2)
and then press the black key B (g. 2) and wait until
the blade reaches its maximum rpm. - Make the cut
desired.
After the cut has been made, press the lever A (g. 2)
and then release it and wait until the blade has come
to a complete stop.
6.8 USING THE STROKE-END GUIDE FOR THE
UPPER TABLE (g. 9)
Proceed as follows: - Insert the guide G (g. 9) in the
upper table – Select the desired cutting width using the
graduated scales – Lock into the guide G into position
using the knob H.
6.9 CUTTING SMALL PIECES
Small pieces must be worked with the use of the correct
tools – On the lower table: Use the clamp to lock the
workpiece in place and the stroke-end rods to obtain the
size desired – On the upper table: Use the pusher (g.
20) provided to advance the workpiece.
Never put your hands on the workpiece to be cut.
Keep the pusher in a safe place nearby for use
whenever required.
6.10 CUTTING LARGE PIECES
Never remove the workpieces that have already been
cut or other parts of the workpieces to be cut while the
machine is working and the support is not in rest position.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Felisatti NTF250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Felisatti NTF250 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info