677768
26
Verklein
Vergroot
Pagina terug
1/50
Pagina verder
Temperature control in Multi-Boiler machines
English 24
20. Temperature control in Multi-Boiler machines
If the machine is a multi-boiler machine, it will have a digital temperature adjusting system, independent for
each brewing group.
There are the following types of multi-boiler machines depending on the machine line:
1 group 2 boilers.
2 groups 3 boilers
3 groups 4 boilers.
The temperature control is performed by a PID thermostat, which get an unbeatable temperature output stability
and control.
20.1. Normal mode
Note that in each brewing group there is a numeric display and
two keypads: “
^” y “v”. Corresponding to each thermostat
During normal mode, each display shows the current
temperature for each group.
The little dot shows when the heating element is active in each
boiler. “Heating element signal”.
20.2. Disconnection of each thermostat
Pressing the button “^” for more than 2 seconds, will make the corresponding
thermostat to turn off; the display will show “OFF” and the group will begin to cool
down.
20.3. Conection of each thermostat
To activate each thermostat (if it was “oFF”) press any of the buttons “^” or “v”. It will switch to normal mode.
20.4. Adjusting group temperature
To adjust the temperature set for each group, proceed as following:
Being the machine connected and the thermostat in normal mode:
Press briefly the button “v”. The thermostat will show on the display the
message “PrG”:
Inmediately, press briefly the button “^”, the display will show the setting temperature “set point”.
Increase or decrease the value of this temperature through the buttons: “^” (+) y “v” (-).
Have in mind, that after 3 seconds since the last actuation on the buttons,
the thermostat will automatically come back to the normal mode.
20.5. Factory defaults / Reset of parameters
If, due to any reason, the working parameters of the thermostat became de-configured, or just an abnormal
performance of the brewing group temperature was observed; don’t have any doubt, it will be very likely solved
by resetting the parameters of the thermostat, coming it back to factory defaults. To perform a factory reset:
Being the machine switch off, keep pressed the button “
^” and turn it off without releasing it.
When the machine shows “PrS”, release the button.
To get to normal mode, just switch off and again on the machine from the
main switch..
20.6. Alarms of the thermostat
Case the temperature probe got disconnected, the display will show the error “A1”.
Case the temperature probe got shor-circuited, the display will show the error “A2”.
^
v
^
v
^
v
^
v
^
v
.
Heat element signal
Current group temp.
^
v
^
v
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Expobar Office bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Expobar Office in de taal/talen: Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 1,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info