668835
40
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
- Wait and make sure that the combustion of pellets left in the brazier has been completed.
- RESET THE SAFETY THERMOSTAT located on the rear of the stove under the outlet (see Fig.
14).
Before resetting the safeties, make sure that the stove is off and completely cooled down,
then proceed as follows:
1 Unscrew the cap located on the rear lower right of the stove (see Figure 14).
2 Press the red button with slight pressure.
3 Replace the cap in its housing.
4 After having cleaned the brazier, re-start the stove by pressing button (4).
8.1.3 Smoke temperature sensor
The smoke sensor is directly connected to the circuit board and keeps operating temperature of
exhaust fumes from the stove under constant control, allowing safe use of the stove.
How it works
If fume temperature exceeds the first pre-set temperature limit, the board passes into modulation
mode. The display will show the message MODULATE / MAX SMOKE”. At the same time if,
despite passage to modulation, the fume temperature continues to increase and exceeds the
second pre-set safety limit, the stove will pass into alarm mode. Pellet flow is interrupted and fume
exhaust speed is set to maximum.
The display will show the message “AL 3 – SMOKE TEMP”.
What to do
- Put the stove in stand-by by pressing the off button for a few seconds (4).
-
Wait and make sure that the combustion of pellets left in the brazier has been completed.
-
Verify and remove the causes which caused the safety devices to go off.
-
After having cleaned the brazier, re-start the stove by pressing button (4).
Smoke sensor fault
The stove constantly controls smoke sensor functioning.
When it activates
If the sensor is momentarily and/or accidentally removed from its housing, or the connector is not
correctly positioned on the circuit board or the sensor fails for any reason. The fault is signalled via
display message AL 2 – “SMOKE SENSOR”.
What to do
1 Put the stove in stand-by by pressing the off button for a few seconds (4).
2 Wait and make sure that the combustion of pellets left in the brazier has been completed.
3 If necessary, call a service centre to replace the sensor.
8.1.4 Water temperature sensor
The water sensor is directly connected to the circuit board and keeps operating water temperature
in the boiler under constant control, allowing safe use of the stove.
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Eva Calor Hydro Slim Kantina 16 kW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Eva Calor Hydro Slim Kantina 16 kW in de taal/talen: Engels als bijlage per email.

De handleiding is 5,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info