722072
39
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
ENDURO
®
autoSteady 32
Ref: AS101-UM-TKI-0114-Rev. A
Ensure that there is no force and movement on the cables. Also avoid any loops.
Route the motor cables along the underside of the caravan floor, and through the drilled hole.
Protect the electrical cables against sharp edges (for example near the chassis) by the supplied convoluted
cable trunking (26). Please can cut the trunking to the correct length.
Secure the motor cables and the cable trunking (26) under the body of the caravan by using the cable ties (17)
or P-Clips (14 & 15) and screws (13).
Please ensure the motor cables are fixed very tightly near the corner steady, and the cables
do not interfere with any part of corner steady when it is drawn back completely.
Once the motor cables are through the drilled hole next to the control unit (6), cut the cables. Ensure that they
are all the same length. Remove approx. 5mm of the insulation from the ends. Fix the spade fork connectors
(23) on the motor-cable ends by using crimping pliers. A secure and good quality connection on each cable is
essential.
Attach the spade fork connectors to the terminals on the control unit (see wiring diagram Fig. 8) and fix them
tightly by the screws. A safe and good quality connection on each cable is again essential.
Find a suitable place for the battery power isolation switch (24) which includes an external holder with hinged
cover. Important: The switch must be mounted onto the exterior body of the caravan and be easily
accessible from the outside of the caravan in case of any emergency. The switch must be mounted close
to the location of the battery in order to keep the length of the battery cables to a minimum.
Use the cardboard template to position the hole positions and the drill holes. Mount the switch and the housing
with the bolts, washers and nuts, and finally mount it on the caravan with stainless steel screws (13).
Route the positive (+) power cable (including fuse) from the battery to the battery power isolation switch (24)
and then further to the control unit (6).
Cut the positive power cable to an appropriate length and remove approx. 5mm of the insulation from the ends.
Fix the O-ring connectors (22) by using crimping pliers. A secure and good quality connection on each cable is
essential.
The electronic connections of the battery power isolation switch (24) must be covered by the supplied rubber
isolation shells (25).
Route the negative (-) power cable directly from the battery to the control unit (6).
No cables may be routed over the control unit!
Again it is recommended to use the supplied trunking (26) to protect the cables against sharp edges. Attach the
cables and trunking with the cable ties (17) or P-clips (14 & 15) and P-clip screws (13).
Cut the cables to an appropriate length and remove approx. 5mm of the insulation from the ends. Fix the spade
connectors (23) by using crimping pliers. A secure and good quality connection on each cable is essential.
Connect the battery cables (19 & 20) to the control unit (6): Attach the spade fork connectors to the positive
(+) en negative (-) terminal of the control unit and fix them tightly by the screws.
Connect the battery cables to the existing battery terminals (red = positive, black = negative). Two types of
battery terminal connector (21 & 22) are provided for use as appropriate.
Caution! Make sure that you do not reverse the positive (+) and negative (-) connections.
Incorrect connection (reverse polarity) will result in damage to the control unit.
Seal 25mm hole in vehicle under body using plastic body sealant.
Next you can connect the cable for the emergency draw back function (option, not obliged). If you forget to
draw back the corner steady before you start to drive, the corner steady or your caravan can get significant
damage. This emergency draw back function ensures that (if installed properly!) the corner steady will be
drawn back automatically when the caravan is connected on the constant 12V power source of the car (via 7 or
13 pin plug).
Connect one end of the blue cable for the emergency draw back function (18) to the constant power source
(+12V) of the car (via 7 or 13 pin connector) and not in direct connection is with the caravan battery! You can
also find this constant power source in the 12V central distribution box of your caravan. It is normally used to
use your refrigerator during driving. If necessary measure again with a multimeter.
39

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Enduro AS101 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Enduro AS101 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 5,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info