722072
38
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
ENDURO
®
autoSteady 31
Ref: AS101-UM-TKI-0114-Rev. A
Check if every pin on the spindle has been mounted tightly enough and all the parts of the
corner steady are under good condition.
Mount the corner steady back to the bottom of the caravan (chassis) via the existing holes on the bracket (Fig.
7A) of corner steady with the original bolts/nuts. If the original bolts are not long enough to be matched with
the original washers and nuts, please use the supplied alternative flange nuts (27) to replace the original
washers and nuts.
Fully tighten all the nuts and bolts.
Adequate ground clearance: Please notice that the minimum distance between the lowest
line of corner steady and ground is 110mm, no matter what kind of chassis or installation
situation.
Re-check that all bolts/nuts have been tightened!
Mount the ground support plates (11) on the feet of the corner steady with the supplied pins and clips (Fig. 6)
The main mechanical components have now been installed.
INSTALLATION - ELECTRICAL/ELECTRONIC COMPONENTS
Make sure the 12V supply from the battery and any 230V electricity supply are disconnected.
Remove battery cable terminals and disconnect any external electrical power before starting work.
Find a suitable place for the electronic control unit (6), such as a storage area, under a seat or a bed. Make
sure this place is dry and close to the battery (40cm to 60cm). The electronic control unit can be mounted
vertically on a side wall or be mounted flat. When mounted vertically, the connections must point downwards to
avoid any short-circuits by objects falling into.
Fix the electronic control unit (6) securely into position with two screws (12). Note: if the provided screws are
not of suitable length or type for the desired location/material please substitute these as appropriate.
Drill a 25mm hole through the floor of the caravan approximately 150mm centrally in front of the control unit
terminals.
Caution! Take extra care to avoid any chassis members, gas pipes and electrical wires!
Route and connect the motor cables and battery cables in accordance with wiring diagram (Fig 8, top view of
the caravan).
The motor cables have been pre-wired already to each motor (just the motor side). Red = Positive (+) and
black is negative (-).
Open the cover on the control unit (Fig. 9A), to find the connectors for the wires.
The connectors on the electronic control unit (6):
Terminal A-
Terminal A+
Terminal B-
Terminal B+
Terminal C-
Terminal C+
Terminal D-
Terminal D+
Terminal 12V-
Terminal 12V+
Terminal e
Terminal N
Left front motor (-)
Left front motor (+)
Left back motor (-)
Left back motor (+)
Right front motor (-)
Right front motor (+)
Right back motor (-)
Right back motor (+)
Main power (-)
Main power (+)
Automatic draw back function
Not used
See also wiring diagram (Fig. 8).
Notice: Left side means the driver side for Europe continent and the passenger side for the UK.
Mark the motor cables for all motor units using the cable number markers (16). Cable number markers “A” for
left-front motor, “B” for left-back motor, “C” for right-front motor, “D” for right-back motor (Fig. 8).
Caution! Make sure that you do not reverse the positive (+) and negative (-) connections.
Incorrect connection (reverse polarity) can result in damage to the control unit!
38

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Enduro AS101 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Enduro AS101 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 5,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info