621095
10
Verklein
Vergroot
Pagina terug
1/23
Pagina verder
- 19 -
Press this button to escape from this screen, and return to Camera Setup display. If the Save dialog is shown, press ENTER to
exit and save, ESC to exit without saving.
The following is a brief description for each item and its specific operations:
Duration response duration to define at most how long (in seconds) the Alarm Out relay and the Buzzer will keep being
triggered after motion is detected for this camera. However, the Alarm Out relay and the Buzzer will be reset immediately
once the camera returns to normal. Press +/- buttons to adjust the value (3-60 seconds, discrete).
Goto Preset to define the preset position to go to if motion is detected and this camera is a PTZ camera. For more details
about preset locations, please refer to Chapter 7 PTZ Control.
P
re-recordto define how long before motion is detected this camera shall be intensively recorded at Pre-record IPS. Press
+/- buttons to adjust the value (0-10 seconds, discrete). Please note that the actual pre-record time may be shorter than the
value set if the total size of the pre-record pictures exceeds the pre-record buffer size of the system.
Post-recordto define how long after motion is detected this camera shall be intensively recorded at Event Record IPS. Press
+/- buttons to adjust the value (0 second - 60 minutes, discrete).
Alarm Out to define which Alarm Output will be triggered when motion of this camera is detected. Press +/- buttons to
select none (N/A) or one of the Alarm Outputs (1-2).
B
uzzer – to activate the internal Buzzer or not when motion of this camera is detected. Press ENTER or +/- to check/uncheck
this item. The default setting is “ˇ
ˇˇ
ˇ ” - checked.
Log – to log to event logs or not. Press ENTER or +/- to check/uncheck this item. The default setting isˇ
ˇˇ
ˇ
- checked.
S
creen Message to display the event message on the screen or not. Press ENTER or +/- to check/uncheck this item. The
default setting is “ˇ
ˇˇ
ˇ ” - checked.
E
-mailto send the event e-mail to remote station or not. The e-mail will be sent to the predefined receivers when the event
is triggered. Press ENTER or +/- to check/uncheck this item. The default setting is “
” - unchecked.
Detection Settings.. used to setup the motion detection settings, including detection area and sensitivity, when motion is
detected for this camera. Press ENTER in Settings.. to call up Motion Detection Setup (as shown) for this camera. In Motion
Detection Setup, the video area is divided into many small grids, and the area with transparent grids is the area which will be
detected for motion, while gray grids not detected for motion. Besides, there is a (green) Mask window.
The following is a brief description for the operations:
Numeric
Press these buttons to select the camera.
◄►
Press these buttons to move the Mask window.
+
/-
Press these buttons to resize the Mask window.
E
NTER
Press this button to set/reset the area under the Mask window.
M
ODE
Press this button to set/reset the whole video area.
S
EQ
- 20 -
Press this button to decrease the sensitivity, from 10 – 1, for the motion detection of this camera.
C
ALL
Press this button to increase the sensitivity, from 1 – 10, for the motion detection of this camera.
SEARCH
Press this button to test the motion detection of this camera. The detected motion will be shown on the screen. Press this
button again to stop testing.
ESC
Press this button to escape from Motion Detection Setup, and return to Motion Setup.
6.3 Alarm Setup
In Setup Menu display, press
to change the highlighted option to Alarm, and then press ENTER to call up Alarm Setup
display as shown. The Alarm Setup allows the administrator to define the attributes for each alarm input, and the actions if it’s
triggered. There are up to 4 alarm inputs which can be connected to the system.
The general operations are as follows:
◄►
Press these buttons to select the items.
Numeric
Press these buttons to select the alarm input.
C
OPY ( )
Press this button to copy the settings of the focus alarm input to all the following alarm inputs. (eg. focus alarm input is 1, its
settings will be copied to those of alarm inputs 2-4.)
ESC
Press this button to escape from this screen, and return to Setup Menu display. If the Save dialog is shown, press ENTER to
exit and save, ESC to exit without saving.
The following
is a brief description for each item and its specific operations:
Normal State press +/- buttons to select N/A, Close or Open. Please check the signal type, normally close or normally open,
connected to the alarm input terminal on the rear panel of the system. If there’s no signal connected, please select N/A Not
Available, and the following items will not be settable. The default setting is Open.
Focus Camera – the camera corresponding to this alarm input.
Duration response duration to define at most how long (in seconds) the Alarm Out relay and the Buzzer will keep being
triggered after this alarm input is triggered. However, the Alarm Out relay and the Buzzer will be reset immediately once this
alarm input returns to normal. Press +/- buttons to adjust the value (3-60 seconds, discrete).
Goto Preset – to define the preset position to go to for the Focus Camera if this alarm input is triggered and the Focus Camera
is a PTZ camera. For more details about preset locations, please refer to Chapter 7 PTZ Control
.
Pre-record to define how long before this alarm input is triggered the Focus Camera shall be intensively recorded at
Pre-record IPS. Press +/- buttons to adjust the value (0-10 seconds, discrete). Please note that the actual pre-record time may
be shorter than the value set if the total size of the pre-record pictures exceeds the pre-record buffer size of the system.
Post-recordto define how long after this alarm input is triggered the Focus Camera shall be intensively recorded at Event
Record IPS. Press +/- buttons to adjust the value (0 second - 60 minutes, discrete).
Alarm Outto define which Alarm Output will be triggered when this alarm input is triggered. Press +/- buttons to select
none (N/A) or one of the Alarm Outputs (1-2).
Buzzerto activate the internal Buzzer or not when this alarm input is triggered. Press ENTER or +/- to check/uncheck this
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro DVR154S bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro DVR154S in de taal/talen: Engels als bijlage per email.

De handleiding is 1,54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Elro DVR154S

Elro DVR154S Gebruiksaanwijzing - Nederlands - 22 pagina's

Elro DVR154S Gebruiksaanwijzing - Deutsch - 24 pagina's

Elro DVR154S Gebruiksaanwijzing - Français - 19 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info