708667
5
Verklein
Vergroot
Pagina terug
1/49
Pagina verder
Through’ will be disabled to allow free access to the
Control Panel to disarm the system before the
entry-delay expires an alarm occurs.
If access is gained via a zone that is not configured as
‘Master Walk Through’, the ‘Slave Walk Through’ zones
will operate as normal according to their programmed
Entry-Delay setting.
Note: A zone set as a ‘Master Walk Through’ zone
must be configured with an Entry-Delay.
OMIT ZONE
A zone may be temporarily omitted when the system is
armed using the Omit feature. When the system is next
disarmed any zones set to Omit will be cancelled.
ZONE LOCKOUT
If a detector on an active zone is triggered while the
system is armed an alarm condition will occur. After
the programmed alarm duration has expired the alarm
will stop and the system will automatically reset.
Subsequent detectors triggered will again initiate an
alarm condition. If a single zone initiates an alarm
condition more than three times then that zone will be
‘Locked Out’ and any further alarm signals from that
zone will be ignored until the system is disarmed.
Note: The ‘Zone Lockout’ feature can be disabled if
required.
EVENT LOG
The Control Panel incorporates a memory capable of
storing the last 50 system events. This enables the
user to see which user has Armed/Disarmed the
system and if and when any alarms occurred. The
time, date and details of the event type will be recorded
for each system event.
CHIME
Chime is a low security facility for use when the system
is Standby mode. If the Chime feature is ON, and a
detector on a zone that has its Chime function enabled
is triggered, the internal sounder will produce a low
volume warning tone. A typical use of the Chime
function would be to warn that a door or particular area
has been accessed.
VOICE DIALER
If the Voice Dialer is enabled and an alarm condition
occurs, the system will call for help using your recorded
alarm messages and up to four telephone numbers.
When an alarm condition occurs, the telephone voice
dialer (if enabled) will call the first enabled number in
the calling sequence and replay the recorded alarm
messages for the configured ‘Play Time’. The recipient
must acknowledge the message by pressing the
button on their telephone keypad. If the call is
unanswered or an acknowledgment is not received
then the next active number in the dialing sequence will
be called. The dialer will continue calling each
number in turn until either all numbers in the sequence
have been dialed the set number of times or the
sequence is cancelled/acknowledged by the recipient.
DIGITAL DIALER
As an alternative to the Voice dialer the system may be
configured to interface with a central monitoring station.
LATCH KEY
When the system is disarmed the Latch-Key facility, if
enabled, will call the first latchkey phone number and
replay the user message (recorded under user setup)
for the set ‘Play Time’. The recipient must
acknowledge the message by pressing the
button on the telephone keypad. If the call is
unanswered or an acknowledgment is not received
then the second latchkey phone number will be called.
The voice dialer will continue calling each number in
turn until each number has been dialed the set number
of times or the sequence is cancelled/acknowledged by
the recipient.
For example, the latchkey facility is useful to inform
parents that a child has returned from school and
disarmed the system.
ANSWER PHONE
The Control Panel includes an answer-phone facility.
The answer phone will record and store a maximum of
6 messages with each message being limited to a 30s
duration.
Messages may be retrieved either direct from the
Control Panel or by dialing into the system from a
phone.
VOICE MEMO
In addition it is also possible to record messages at the
Control Panel using the ‘Voice-Memo’ facility. Each
voice-memo message is limited to a maximum duration
of 30s and counts as an answer phone message.
REMOTE SYSTEM CONTROL
It is possible to dial into the system via the connected
telephone line to interrogate the system status and to
have basic control over the system, (e.g. to Arm and
Disarm the system). You may also activate the
microphone on the control panel to Listen-In to what is
3
5

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elro-AP5500---Pro-Alarm-System

Zoeken resetten

  • alarm memory lampje brand en piept, hoe kan ik dit oplossen?? Gesteld op 16-4-2024 om 17:14

    Reageer op deze vraag Misbruik melden
  • Het betreft de Elro AP5500, het alarm memory lichtje blijft knipperen en het apparaat geeft regelmatig een piep toon, Het apparaat al gereset , via de sleutel, code, rondje en kruisje. Dan verdwijnt het ongeveer 5 minuten en het begint daarna weer te knipperen enz,. Wat is de oplossing? Gesteld op 29-1-2022 om 11:27

    Reageer op deze vraag Misbruik melden
  • Op mijn installatie knippert regelmatig het Led Status lampje. Weet iemand hoe ik dit uit kan zetten of wat dit betekent?. Het systeem functioneert overigens prima. Gesteld op 17-12-2021 om 16:11

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elro AP5500 - Pro Alarm System bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elro AP5500 - Pro Alarm System in de taal/talen: Engels als bijlage per email.

De handleiding is 3,52 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Elro AP5500 - Pro Alarm System

Elro AP5500 - Pro Alarm System Snelstart handleiding - Nederlands - 8 pagina's

Elro AP5500 - Pro Alarm System Gebruiksaanwijzing - Nederlands - 42 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Deutsch - 10 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - English - 8 pagina's

Elro AP5500 - Pro Alarm System Snelstart handleiding - Français - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info