612699
88
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
ISO 15765-4 format. Try resending the command
again – if it was a noise burst, it may be received
correctly the second time.
ERRxx
There are a number of internal errors that might be
reported as ERR with a two digit code following. These
occur if an internally monitored parameter is found to
be out of limits, or if a module is not responding
correctly. If you witness one of these, contact Elm
Electronics for advice.
One error that is not necessarily a result of an
internal problem is ERR94. This code represents a
‘fatal CAN error’, and may be seen if there are CAN
network issues (some non-CAN vehicles may use pins
6 and 14 of the connector for other functions, and this
may cause problems). If you see an ERR94, it means
that the CAN module was not able to reset itself, and
needed a complete IC reset to do so. You will need to
restore any settings that you had previously made, as
they will have been returned to their default values.
Beginning with v1.3a of this IC, an ERR94 will also
block further automatic searches through the CAN
protocols, if bit 5 of PP 2A is a ‘1’ (it is by default). This
is done because most ERR94s will be as a result of
serious CAN wiring problems. Blocking of the CAN
protocols remains in effect until the next power off and
on, or until an AT FE is sent.
FB ERROR
When an OBD output is energized, a check is
always made to ensure that the signal also appears at
the respective input. If there is a problem, and no
active input is detected, the IC turns the output off and
declares that there was a problem with the FeedBack
(FB) of the signal. If this is an initial trial with your
ELM327, this is almost certainly a wiring problem.
Check your wiring before proceeding.
LP ALERT or !LP ALERT
This appears as a warning that the ELM327 is
about to switch to the Low Power (standby) mode of
operation in 2 seconds time. This delay is provided to
allow an external controller enough time to prepare for
the change in state. No inputs or voltages on pins can
stop this action once initiated. Note that the ‘!’ before
LP ALERT is printed if PP 0F bit 1 is 1.
Error Messages and Alerts (continued)
LV RESET
The ELM327 continually monitors the 5V supply to
ensure that it is within acceptable limits. If the voltage
should go below the low limit, a ‘brownout reset’ circuit
is activated, and the IC stops all activity. In rare cases,
a sudden large change in VDD can also trigger a low
voltage reset.
When the voltage returns to normal, the ELM327
performs a full reset, and then prints LV RESET. Note
that this type of reset is exactly the same as an AT Z
or MCLR reset (but it does not print ELM327 v2.1).
An LV RESET will also block automatic searches
through the CAN protocols, if bit 4 of PP 2A is a ‘1’ (it
is by default). This is done because most LV RESETs
seem to occur as a result of CAN wiring problems (the
transceiver is capable of passing very large currents).
Blocking of the CAN protocols is only done until the
next reset (AT Z, WS, etc.) or until an AT FE is sent.
NO DATA
The IC waited for the period of time that was set
by AT ST, and detected no response from the vehicle.
It may be that the vehicle had no data to offer for that
particular PID, that the mode requested was not
supported, that the vehicle was attending to higher
priority issues, or in the case of the CAN systems, the
filter may have been set so that the response was
ignored, even though one was sent. If you are certain
that there should have been a response, try increasing
the ST time (to be sure that you have allowed enough
time for the ECU to respond), or restoring the CAN
filter to its default setting.
<RX ERROR
An error was detected in the received CAN data.
This most often occurs if monitoring a CAN bus using
an incorrect baud rate setting, but it may occur if
monitoring and there are messages found that are not
being acknowledged, or that contain bit errors. The
entire message will be displayed as it was received (if
you have filters set, the received message may not
agree with the filter setting). Try a different protocol, or
a different baud rate.
STOPPED
If any OBD operation is interrupted by a received
RS232 character, or by a low level on the RTS pin, the
88 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
88

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info