612699
87
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
Error Messages and Alerts
?
This is the standard response for a misunderstood
command received on the RS232 input. Usually it is
due to a typing mistake, but it can also occur if you try
to do something that is not appropriate (eg. trying to do
an AT FI command if you are not set for protocol 5).
ACT ALERT or !ACT ALERT
This message occurs as a warning that there has
been no RS232 or OBD activity for some time (see the
Power Control section for details). If allowed, the IC
will be initiating a switch to the Low Power (standby)
mode of operation. If this was initiated by no RS232
activity, sending something within the next minute will
stop the switch to low power. Note that the ‘!’ before
ACT ALERT is printed if PP 0F bit 1 is 1.
BUFFER FULL
The ELM327 provides a 512 byte internal RS232
transmit buffer so that OBD messages can be received
quickly, stored, and sent to the computer at a more
constant rate. Occasionally (particularly with CAN
systems) the buffer will fill at a faster rate than it is
being emptied by the PC. Eventually it may become
full, and no more data can be stored (it is lost).
If you are receiving BUFFER FULL messages,
and you are using a lower baud data rate, give serious
consideration to changing your data rate to something
higher. If you still receive BUFFER FULL messages
after that, you might consider turning the headers and
maybe the spaces off (with AT H0, and AT S0), or
using the CAN filtering commands (AT CRA, or CM
and CF) to reduce the amount of data being sent.
BUS BUSY
This occurs when the ELM327 tries to send a
message, or to initialize the bus, and detects too much
activity to do so (it needs a pause in activity in order to
insert the message). Although this could be because
the bus was in fact very busy, it is almost always due
to a wiring problem that is giving a continuously active
input. If this is an initial trial with your new ELM327
circuit, then check all of the voltage levels at the
offending OBD input, as this error is very likely due to
a wiring problem (see our ‘AN02 - ELM327 Circuit
Construction’ for some typical voltages).
BUS ERROR
A generic problem has occurred. This is most
often from an invalid signal being detected on the bus
(for example, a pulse that is longer than a valid Break
signal), but usually is from a wiring error. Note that
some vehicles may generate long pulses as part of
their startup process, so you may see this message as
part of a normal vehicle startup while ‘monitoring all.’
CAN ERROR
The CAN system had difficulty initializing, sending,
or receiving. Often this is simply from not being
connected to a CAN system when you attempt to send
a message, but it may be because you have set the
system to an incorrect protocol, or to a baud rate that
does not match the actual data rate. As with BUS
ERRORs, the CAN ERROR might also be the result of
a wiring problem, so if this is the first time using your
ELM327 circuit, review all of your CAN interface
circuitry before proceeding.
DATA ERROR
There was a response from the vehicle, but the
information was incorrect or could not be recovered.
<DATA ERROR
There was an error in the line that this points to,
either from an incorrect checksum, or a problem with
the format of the message (the ELM327 still shows
you what it received). There could have been a noise
burst which interfered, possibly a circuit problem, or
perhaps you have the CAN Auto Formatting (CAF) on
and you are looking at a system that is not of the
The following shows what the ELM327 will send to
warn you of a condition or a problem. Some of these
messages do not appear if using the automatic search
for a protocol, or if the Programmable Parameter bits
disable them.
87 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
87

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info