612699
84
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
Modifications for Low Power Standby Operation
If you wish to semi-permanently install your
ELM327 circuit in a vehicle, current consumption
quickly becomes an issue. A typical ELM327 circuit
draws about as much current as a dome lamp, so can
not be left on for long without the vehicle’s engine
running.
When it is not needed, the ELM327 may be placed
in a low power ‘standby’ mode in which it consumes
very little current. Reducing the integrated circuit
current itself is generally not enough, however, as you
must also consider the current drawn by the other
components as well.
The following discussion takes the circuit of Figure
9, and modifies it slightly in order to highlight our
suggestions for reducing current consumption. The
resulting circuit (Figure 15) is shown following. Note
that portions of the circuit that are the same as Figure
9 are shown in grey, while the changes that we are
making are shown in black.
Consider the circuit of Figure 9 in the Example
Applications section. With 12V to 15V applied to the
‘Battery Positive’ input, the total current used by this
circuit is typically:
base current = 29.8 mA
Without making any wiring changes, you can
reduce this current by placing the ELM327 into the
low power standby mode. This only requires sending
the Low Power command (AT LP), after which the
current would typically drop to:
current after AT LP = 17.6 mA
This reduction is due entirely to the change in the
ELM327’s operating current (it only needs a very small
current to stay in standby mode). But where is the
other current coming from? One obvious load is the
LED that shows that the power is on. The other is the
CAN transceiver IC, U2. By disconnecting the common
connections from R24 and R31, and then returning
both to pin 16 of the ELM327, we can switch the
current that these two use. With this change (which is
shown as modification #1 in Figure 15), the current
after AT LP drops further:
current after mod #1 = 8.2 mA
There is a considerable current still flowing in the
circuit at this point, but it should mainly be the voltage
regulators that are using it. In the next step, we will
change U3 (a 7805) to an LP2950ACZ-5.0G, and see
how effective that is. While the LP2950 is a good
choice for its lower quiescent current, it does suffer
from stability problems if you do not provide capacitive
loading as shown. Note that the 4.7uF capacitor is
tantalum, while the 2.2µF one is aluminum. At this
point it may also be useful to review our Application
Note ‘AN03 - ELM327 Low Voltage Resets’, as you
may want to use an even larger capacitor on the 5V
side. After changing U3 for an LP2950, the current is
typically:
current after mod #2 = 3.5 mA
If we continue to reduce the load currents beyond
this point, we will quickly get to a point where any
currents injected from external sources (ie. through the
protection diodes at inputs such as pins 2 or 12) will
become significant compared to the load currents. If
these currents should exceed the load current, the Vdd
voltage will rise and damage might result. To prevent
the voltage from rising too high, we recommend that
you add either a zener diode or a transient voltage
suppressor (TVS), directly across the 5V supply, as
shown in the top right corner of Figure 15. Suggestions
for devices to consider are the 1N5232B zener diode
or the SA5.0AG TVS.
Another integrated circuit that is not changing
current during low power mode is the 317L (U4). In
fact, a quick calculation shows that it is likely using
about 2.6 mA when idle, which is very significant. If we
replace this IC with another that uses less current, we
will be close to getting the total circuit current to less
than 1 mA.
Figure 15, modification #3 shows an LP2951ACM
regulator in the circuit, as a replacement for the 317L.
It uses much less current than the 317 during normal
operation, and offers a shutdown control input as well
to further reduce current when it is not required. Note
that the LP2951 circuit needs the ELM327 to provide a
high level at pin 3 for a 5V output, and a low for 8V, so
an inversion is needed. To do this, set PP 12 to 00
with:
>AT PP 12 SV 00
>AT PP 12 ON
then reset the chip, and the voltages will always be
correct for J1850 from that point on.
Note that the LP2951 regulator also requires a
84 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
84

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info