612699
82
Verklein
Vergroot
Pagina terug
1/94
Pagina verder
Example Applications (continued)
82 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
ELM327
the rest.
We do caution that the MAX3222E does seem to
place some extra demands on the 5V power supply. It
should work fairly well with the 7805 regulator that we
show in Figure 9, but if you have chosen a lower
current device like the 78L05 or LP2950, you may
experience occasional ‘LV RESET’s. If you do, we
recommend adding two capacitors to the circuit of
Figure 9. We suggest that a 10 µF 50V capacitor be
connected in parallel with C1, and also that a 33 µF
10V unit be installed across C5 (the 5V ‘rail’). This
should eliminate problems, but if it does not, you may
also wish to consider a more powerful regulator (such
as the 7805 that we show in Figure 9) if you do not
already have one installed.
The USB interface of Figure 13 provides another
way to connect the ELM327 to USB systems. It uses a
Silicon Laboratories (www.silabs.com) CP2102 chip to
convert between the ELM327’s serial data and USB.
One of the advantages of going to a USB interface
is the high serial baud rates that you may experience.
In order to use these higher rates, you will have to
program both the USB interface and the ELM327
interface for them.
The CP2102 interface baud rate is actually
configured by driver software. When you set the baud
rate in your terminal program, the software does what
is necessary to configure the CP2102 for operation at
that rate and you do not need to do anything more.
The ELM327 initially only uses a 38,400 bps rate,
however, and must be told to use anything different.
In order to change from the standard 38.4 k baud
rate, you must first set your software to 38.4 kbps, and
power up your ELM327 circuit. Make sure that it is
working, as described in the ‘Communicating with the
ELM327’ section, before you do anything else. When
you are confident that all is well, you can then change
the baud rate. Before doing so, we caution that you
should check to be sure that your software actually
supports the desired rate (as several can not handle
more than about 250 kbps).
The CP2102 chip is able to support a 115.2 kbps
rate natively, and almost all software should be able to
support it as well, so we will use that rate to provide an
example.
First, while connected to the ELM327 at 38.4 kbps,
we need to change the default rate to 115.2 kbps. No
need to worry that this will affect your communications,
as it will not take effect until the ELM327 has been
reset. To change the data rate, simply change the
Figure 12. An High Speed
RS232 Interface ( 250 kbps)
2 (RxD)
3 (TxD)
5 (SG)
1 (DCD)
4 (DTR)
6 (DSR)
7 (RTS)
8 (CTS)
0.1µF
1
2
3
4
5
6
7
8
9
RS232
Interface
(DB9F)
+5V
0.1µF
+5V
327
0.47µF
0.47µF
0.47µF
+5V
327
2 (D-)
USB
Interface
(type ‘B’
connector)
+5V
1 (+5)
4 (SG)
3 (D+)
SiLabs
CP2102
0.1µF
5.0V
TVS
1µF
7
6
26 25
3
4
5
8
Figure 13. An Alternative USB Interface
82

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Elm-327

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elm 327 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elm 327 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info