741485
7
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
(((ELKRON)))
MP110 USER MANUAL
(((ELKRON)))
MP110 USER MANUAL
3.System Arming/Disarming
For ARMING of the system, enter a valid code and press the
TOTAL
key.
all sectors referred to the entered code will be armed. The leds
corresponding to the armed sectors will flash and then turn on in a fixed
mod
If an exit delay occurs, it is indicated by the buzzer with an intermittent
signal .
•To DISARM the system, enter a valid code and press the
TOTAL
key.
Leds
1
3
,
2
and
3
are turned OFF and the buzzer
beeps twice.
To partially ARM the system, enter a valid code and press the key for
the zone or zones one wishes to arm.
1
to arm Zone 1 - the led
1
3
flashes and lights up with a fixed
light after 4 seconds.
2
to arm Zone 2 - the led
2
flashes and lights up with a fixed
light after 4 seconds.
3
to arm Zone 3 - led
3
flashes and lights up with a fixed light
after 4 seconds.
To DISARM the system, enter a valid code and press the
TOTAL
key. The
leds of the previously armed zones are turned OFF and the buzzer
beeps twice.
During partial arming, about 5 seconds are available (led flashing time)
within which it is possible to correct the type of arming; once this time
is up, the leds light up with a fixed light and the sectors are armed.
After selecting the desired configuration for the zones, arming can be
confirmed by pressing the
A
key without waiting for the time
available for arming to expire.
3.1 Arming/Disarming
3.2 Partial Disarming
7
If the operation was not successfully performed (for example, because
the key was not removed while led 4 flashed quickly), all leds will flash
quickly to indicate that the operation has failed and that the programming
operation must be repeated. In this case, the message “PROGRAM
ERROR” appears on the alphanumeric display, while the symbol “-”
appears on the led display and all three zone leds flash.
8. Remove the key. Return to item 4 to program the other keys or press
key
F
to exit
2.2 Addition of a Key
1. Enter the MASTER USER code on the keypad and press keys
F
+
7
in sequence.
2. Press the
1
key several times until the following message appears
on the display:
• keypad with alphanumeric display:KEY ADDITION
• keypad with segmented display :
a
(flashing)
3. Press the
7
key. Commutator led 2 flashes slowly to indicate
system standby for entry of the additional key.
4. Proceed in the order described in items 4, 5, 6, 7 and 8 of the previous
section to associate the desired sectors to the key.
2.3 Duplication of a Key Code
1. Enter MASTER code on keypad and press keys
F
+
7
in
sequence.
2. Press key
1
several times until the display shows the following
message:
keypad with alphanumeric display: “READ KEY CODE
keypad with segment display: “
L
” (flashing)
3. Press key
7
. Led 2 of the commutator flashes slowly to show that
the system is waiting for the introduction of the key to be duplicated.
4. Introduce the key to be read. After approx. 2 seconds a double beep
will be generated to confirm that the code has been read. The procedu-
re is terminated and the system has stored the key code. Press key
F
to exit. To make the desired keys operating, follow the procedu-
re “ Addition of a key” , para 2.2.
34
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron MP110TG bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron MP110TG in de taal/talen: Engels als bijlage per email.

De handleiding is 0,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Elkron MP110TG

Elkron MP110TG Gebruiksaanwijzing - Deutsch - 32 pagina's

Elkron MP110TG Gebruiksaanwijzing - Français - 120 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info