741402
12
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
12/40
STEP 2 Board initialization
1. Before proceeding set the following parameters in the Control Unit:
Master Menu ENABLE ADVANCED REMOTE ACCESS = ENABLE
Master Menu ENABLE ADVANCED REMOTE UNSETTING = ENABLE
Installer Menu MAINTENANCE USAGE MODE = MODE 2 or MODE 0
Installer Menu PROGRAMMING SECTORS CONFIGURE SECTORS = STANDARD or
SELF-INHIBITION *
* Operation to be performed on all sectors present.
2. Install the Hi-Connect software (version 3.70 or later) on a PC. To install it, follow the procedure
described in the manual “Hi-Connect Installation and Management”.
WARNING! Windows XP operating system is not supported.
3. Connect the Web server LAN cable directly to the PC.
4. Prepare and set the PC by changing the parameters of the Ethernet card used. Proceed as follows:
a) Select "Start" and type: Control panel
b) A window opens, select “Control panel
c) From "Control panel" select "Network and sharing centre" Note: Make sure that the item
View by:” is set to “Small icons
d) From "Display active networks" select the network displayed in "Connections":
e) A window with the information on the network opens, select "Properties"
f) A window with the network properties opens, double click on "Internet protocol version 4
(TCP/IPv4)".
g) Select “Use the following IP address” and, in “IP address”, type: 192.168.1.10 and in “Subnet
mask”: 255.255.255.0
5. Run the Hi-Connect software (PWD:123456).
6. After logging in, the main window of Hi-Connect menus opens.
Click on “INITIALISE IT500WEB”.
Note: Before proceeding, it is necessary to identify an IP address and the Gateway to assign to the
Web Server. This information can be identified by connecting to the router (e.g. using the Wi-Fi
connection of your PC), where the Web Server will be installed, using the IPCONFIG command.
Proceed as follows:
a) Select "Start" and type: CMD
b) A window opens, select “Command prompt
c) A window opens, type: IPCONFIG and press “Enter
d) The list of the active connections and relevant network parameters is displayed
e) Identify the network parameters (e.g. Wireless LAN card…)
f) For the Web Server, use the IP Address previously identified and increase it by a few
units (e.g. displayed IPv4 Address = 192.168.8.18; Web Server IP Address = 192.168.8.98)
g) For the Web Server, use the default Gateway previously identified
(e.g. displayed default Gateway = 192.168.8.1; Web Server default Gateway = 192.168.8.1)
7. Enter the data prompted by the wizard, those marked with an asterisk are mandatory. Continue by
clicking onNEXT” until the “INITIALISING COMPLETED!” window is displayed.
8. The same screen displays two filled-in fields specifying the MAC Address and the ID Code of the
initialised Web Server.
9. Use “COPY” to save the two codes in a file editor (Word or other), as they are essential for
subsequent registration on the WEB Portal (www.myelkronhome.com)
10. Continue by clicking on “END”.
11. A window with “Save changes made?” is displayed. Select “YES” to save the data.
WARNING! If NO is selected, the data entered in Hi-Connect will be lost, but the Web
Server will be configured with the data entered.
Note: The factory IP address of the Web Server is 192.168.1.100.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elkron IT500WEB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elkron IT500WEB in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 2,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info