753497
16
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
16
ENGLISH
6.4 Connect the gas cylinder
1. Place gas cylinder on Powerbox and
secure with chain against turning
over.
2. Connect gas hose to the SDV (40).
Note:
The SDV is fitted with a solenoid
valve. Gas flows only during the welding
process.
3. Connect gas hose to pressure regu-
lator.
7.1 Control unit for default
machine settings
1. Open SDV cover.
2. Stipulate the welding process set-
tings with the selector switches:
the type of electrode wire (Wire
Type)
the wire diameter (Wire Diame-
ter)
the type of shielding gas (Gas
Type)
the operating mode (Mode Selec-
tion)
the burnback timer (Wire burn-
back control).
7.2 Charateristics curves
The default charateristics curves, sup-
plied with the machine, are selected by
the settings made at the control unit for
the default machine settings.
Example: Charateristics curve for
MIG brazing
MIG brazing is suitable for brazing gal-
vanized sheet metal. To select this cha-
rateristics curve, the following settings
must be made.
Wire type: Cu/CuZn
Gas type: I1 (Argon) or
M12 (0-5% CO2,
balance Argon)
Operating mode: MIG/MAG or
pulsed MIG/MAG.
Note:
The allocation of settings and
corresponding charateristics curves is
shown on the label affixed to the inside
of the cover.
As an option, any charateristics curve
can be changed by a PC via the connec-
tor socket for programming.
Note:
Detailed information about pro-
gramming of characteristic curves is
available from the service centre in your
country (see address listing on back
cover of the spare parts list).
The operating mode PROGRAMM is
reserved for charateristics curve pro-
gramming.
7.3 Gas type
I1 = 100% Argon
M13 = 0-3% O2, balance Argon
M12 = 0-5% CO2, balance Argon
M21 = 0-25% CO2, balance Argon
7.4 Pulsed MIG/MAG
2-step = manual welding operation:
1. Actuate the torch trigger
The welding process starts.
2. Release the torch trigger
The welding process ends.
4-step = continuous welding operation:
1. Actuate and release the torch trigger
The welding process starts.
2. Actuate and release the torch trigger
again
The welding process ends.
4-step+H = continuous welding operation +
High-Start:
1. Actuate the torch trigger
Welding current and wire feed
speed are increased by 25% over
the set values.
2. Release the torch trigger
The welding process runs at the set
values.
3. Actuate the torch trigger again
The welding process will then run at
a reduced welding current (rated
current reduction).
4. Release the torch trigger
The welding process ends.
ABS (reduced value for end crater fill-
ing)
With the ABS function the parameters of
the charateristics curve are reduced for
the pulsed MIG/MAG welding process
for best welding results. The end of the
weld is welded with reduced power and
end craters are prevented.
The ABS function is dependent on the
selected wire type.
7.5 MIG/MAG
2-step = manual welding operation:
1. Actuate the torch trigger
The welding process starts.
2. Release the torch trigger
The welding process ends.
4-step = continuous welding operation:
1. Actuate and release the torch trigger
The welding process starts.
2. Actuate and release the torch trigger
again
The welding process ends.
Integrated softstart
The machine features an integrated soft-
start for the MIG/MAG and pulsed MIG/
MAG welding modes.
As long as there is no welding current
flow, the electrode wire is fed very
slowly. This prevents to much wire emer-
gence. As soon as the arc starts the wire
is fed at the preset speed.
Note:
In position EXT (MIG/MAG and
pulsed MIG/MAG) an external control
can be connected.
If this operating mode is selected and no
external control connected, the machine
operates in 2-step mode.
7.6 Manual arc welding
ELECTRODE:
After arc start the welding process
run for a brief period with an
increased welding current (inte-
grated Hot-Start).
The welding current increase for the
intergrated Hot-Start is 25% of the
set welding current.
Example:
Welding current = 100 A
Current increase = 25%
=> Hot-Start current = 125 A.
7.7 FBZ Burnback time
If set correctly, the burnback timer keeps
the electrode wire from sticking to the
weld pool. Adjustment is made with the
selector switch Burnback Time. The
scale values of 1-10 correspond to a
burnback time range of 0…0.4 s.
7. Default Machine Settings
40
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Elektra Beckum Mig Mag 232EP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Elektra Beckum Mig Mag 232EP in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 3,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info