700190
18
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
18
ENGLISH
FUNCTIONAL INSTRUCTIONS
INTERCONNECTION EXAMPLE
2-channel-mode: 1 x Stereo-System (Front or Rear)
INTERCONNECTION
Connect the RCA outputs of the head unit with the RCA jacks (INPUT L/R) of the amplier with appropriate high-value RCA cables.
Connect the front and rear speakers with the speaker outputs (SPEAKER OUTPUT + L - and + R -).
Always ensure that the total impedance load on the speaker outputs is not lower than 2 ohms.
Too low impedance cause high temperature and will shut down the amplier operation.
Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
CROSSOVER SETTINGS
When using bigger speakers (more than 20 cm) set the X-OVER switch to the FULL position (Full Range Signal).
When using smaller speakers (8.7cm - 16 cm) set the X-OVER switch to the HP position (Highpass Mode) to avoid any damage
by lower frequencies on the speakers. The cut-off frequency is adjustable with the HIGH PASS controller and should be set between
60Hz to 150Hz, depending on the size of the speakers.
The LOW PASS controller is not in use in this interconnecting example.
LEVEL CONTROLLER
Turn the LEVEL INPUT controller of the amplier to the MIN position.
Turn the volume controller of the head unit to 80 - 90% of its full setting.
Turn the LEVEL INPUT controller clockwise until you hear some distortion.
Then turn back the LEVEL INPUT controller slightly until you hear a cleaner sound.
BASS BOOST CONTROLLER
The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .
BASS REMOTE
The enclosed BASS REMOTE CONTROLLER is not in use in this interconnecting example.
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity of all connections.
NOTE
INPUT OUTPUT
L
R
L
R
LEVEL INPUT
HIGH
PASS
LOW
PASS
BASS
BOOST
HIGH LEVEL INPUT
REMOTE
AUTO
TURN-ON
MIN
DC OFFVOX
MAX 10 Hz 500 Hz 50 Hz
5000 Hz
0dB
12dB
POWER INPUT
GND REM
IN/OUT
+12V
POWER
PROTECT
BAND
PASS
X-OVER
FULL LP/BPHP
L + + R
SPEAKER OUTPUT
BRIDGED
QL500.2
Connect stereo RCA outputs (FL/FR or RL/RR) of
the head unit with INPUT L / R
of the amplier
HP od. FULL
Loudspeaker
right
2 – 8 Ohms
Loudspeaker
left
2 – 8 Ohms
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ESX QL500.2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ESX QL500.2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info