700190
16
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
16
ENGLISH
FUNCTIONAL INSTRUCTIONS
9
The LEVEL INPUT controller determines the input sensitivity (adaptation to the output signal of the head unit). The controller
range is between 5 volts (MIN) and 0.2 volts (MAX).
OPERATING ELEMENTS
7
8
Connect the INPUT RCA jacks with the head unit by using appropriate audio signal cables.
The OUTPUT RCA jacks provide a linear full-range audio signal for driving additional ampliers.
13
12
The X-OVER switch selects the desired operating mode:
FULL: Full-Range mode (the entire frequency range is amplied).
HP: High-Pass mode (frequency is limited downwards, adjustable by the HIGH PASS controller).
LP/BP: Low-Pass/Bandpass mode (frequency is limited upwards, adjustable by the LOW PASS controller). The HIGH PASS
controller then acts as a subsonic lter in this mode and limits the frequency downwards (bandpass function).
NOTE: If this is set higher than the LOW PASS, no sound is heard.
The LOW PASS controller determines the frequency cut-off upwards. The crossover frequency is continuously variable from 50
Hz to 5000 Hz (5 kHz).
10
If your head unit does not have a turn-on signal (REM), you can use the automatic turn-on function of the amplier. This works
in two ways, which can be set at the AUTO TURN-ON switch:
DC: This method only works if you use the amplier’s HIGH LEVEL INPUT. The amplier then detects a voltage rise to 6 volts
when the head unit is turned on by a so-called “DC offset” and then turns on the amplier.
VOX: Select this method when using the INPUT RCA jacks. The amplier then detects a voltage increase in the incoming audio
signal when switching on the head unit via the attached RCA cable and then switches on the amplier.
Note: As soon as the head unit is switched off again, the amplier switches itself off.
The terminal for the amplier turn-on (page 15#2, REM IN/OUT) can now be used to supply additional ampliers with a turn-on
signal. Simply connect the REM terminals of the two ampliers and make sure that the other amplier is in “normal” turn-on
mode, which means that the AUTO TURN ON function is disabled.
6
If the POWER/PROTECT is green, the amplier is ready for operation. If the POWER/PROTECT is red, there is a malfunction.
Refer in this case to the section TROUBLE SHOOTING.
11
The HIGH PASS controller determines the frequency cut-off downwards. The crossover frequency is continuously variable from
10 Hz to 500 Hz.
INPUT OUTPUT
L
R
L
R
LEVEL INPUT
HIGH
PASS
LOW
PASS
BASS
BOOST
HIGH LEVEL INPUT
REMOTE
AUTO
TURN-ON
MIN
DC OFFVOX
MAX 10 Hz 500 Hz 50 Hz
5000 Hz
0dB
12dB
POWER INPUT
GND REM
IN/OUT
+12V
POWER
PROTECT
BAND
PASS
X-OVER
FULL LP/BPHP
L + + R
SPEAKER OUTPUT
BRIDGED
QL500.2
8 9 11 12 13 14
157 6 10 16
16

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw ESX QL500.2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van ESX QL500.2 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 2,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info