761230
15
Verklein
Vergroot
Pagina terug
1/64
Pagina verder
15
L N
6mm
L N
6mm
3.1
Rear cable entry.
4 5
Connecting to terminal block. Attaching main body.
Warning: Risk of electric shock!
Ensure power is not connected.
1. Ensure the cable does not sit above
the cable guide from the cable inlet
to the terminal block. If the cable
sits above the guide walls it may
interfere with main components,
prevent the security screws being
fitted correctly, or risk the main body
being forced on to the backplate,
causing damage.
2. Unscrew the cable clamp from
the backplate. Remove the cable
terminal block.
3. Open the flap on the terminal
block. Secure the live, neutral and
earth wires into the correct terminal
locations as indicated on the
terminal block casing.
4. Verify the connections are correct
before proceeding.
5. Close the flap on the terminal block
and fit it into the backplate.
6. Screw in and secure the cable clamp.
CAUTION: DO NOT OVERTIGHTEN
AND CRUSH THE POWER CABLE.
CAUTION: Do not overtighten screws.
1. Hook the main body of the unit over
the top rim of the backplate.
2. Swing the main body of the unit
down on to the back plate. (For
installations with the cable entry on
the side, ensure that the side bracket
seal is correctly seated against the
main body.)
3. Insert and tighten the (2) security
screws into the side of the main body
with the service tool as illustrated.
Recommended torque of 0.5-
0.7NM.
4. Turn power on.
5. Test unit for correct operation.
IMPORTANT
DO NOT USE SEALANT WHEN
FIXING THE UNIT TO THE WALL.
DO NOT PAINT/COAT THE MAIN
BODY OR PLACE GRAPHICAL
STICKERS ON IT OR THIS MAY
DAMAGE THE ANTI-BACTERIAL
SURFACE.
IF A CLEANING PRODUCT IS LEFT
ON THE MACHINE FOR TOO LONG,
A FILM WILL FORM. THIS MAY
REDUCE THE EFFECTIVENESS OF THE
ANTI-BACTERIAL SURFACES.
electricity supply cable from the wall
must align with rear cable entry point
in the backplate.
4. Mark the location on the wall with a
pencil. Use the backplate to mark the
locations for the four fixing points.
5. Drill holes.
6. Fix the optional back panel if
required.
Fixing the backplate to the wall.
Fit the backplate securely to the wall
using the appropriate fixings for the
wall type and weight of the unit. Do
not use counter-sunk screws.
Do not secure tightly until after the
power cable has been secured.
Installing the power cable.
1. Cut the entry hole in the rubber
cable grommet to the correct size:
leave a hole smaller than the
diameter of the power cable to
ensure the cable fits tightly.
2. Pull the cable through the
grommet. Ensure the cable is long
enough to route correctly through
the backplate to the terminal
block.
The cable must sit in the
dedicated channel.
3. Fit the grommet into the
backplate. Ensure it is secure.
4. Secure the screws in the
backplate.
5. Proceed with step 4, ‘Connecting
to terminal’.
6mm
● Primary fixing locations (x4).
Do not use countersunk screws.
Secondary fixing locations.
15

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dyson AB12 - Airblade V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dyson AB12 - Airblade V in de taal/talen: Alle talen als bijlage per email.

De handleiding is 19,46 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Dyson AB12 - Airblade V

Dyson AB12 - Airblade V Aanvulling / aanpassing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info