Handleiding Dimplex CAS 1000R (pagina 14 van 56) (Nederlands, Duits, Engels, Frans, Italiaans, Pools)

706337

Verklein

Vergroot

Pagina terug

1/56

Pagina verder

GENERAL TIPS

Only use ltered/decalcied water in this appliance.

Always ensure that the appliance is sitting on a level surface.

If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.

Once installed, never move this appliance or lay on its back, without draining the water from sump.

CLEANING

Warning – Always press Switch ‘A’ to the ‘OFF’ (0) position (Fig 21) and disconnect from the power supply before

cleaning the re.

We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:

Sump, Nozzle, Tank cap and seal, Air lter

For general cleaning use a soft clean duster – never use abrasive cleaners.

To remove any accumulation of dust or uff, the soft brush attachment of a vacuum cleaner should occasionally be used.

Sump

1. Press Switch ‘A’ to the ‘OFF’ (0) position (Fig 21)

2. Gently lift off the fuel bed and place it aside.

3. Remove the water tank from its position on top of the sump.

4. Disconnect the electrical connector to the transducers, located on the right side of the sump. (Fig 23).

5. There are two orange clips holding down the nozzle on the sump; one on the left and one on the right hand side of

the nozzle. On the left side, press in the clip with one hand and with the other lift the nozzle out of the clip. Repeat

this for the right side (Fig 24). The nozzle can now be lifted up and placed aside (Fig 25).

6. Gently lift up the sump (Fig 26), taking care to keep it level so as not to spill any water. Sit the sump in the sink.

7. Carefully empty the sump into the sink taking note that the transducer is held in place by a retaining clip.

Maintenance

7. When all products are paired, test the remote control by pressing the button. If any of the products fail to receive

a signal from the remote control you can bring that product back in line with the others via the Manual Controls or

the receiver controls.

GETTING THE DESIRED FLAME EFFECT

1. Switch the appliance on by pressing the main switch to the on position and pressing the button. The ames will

start after 45seconds.

2. Press the and buttons to adjust the ame to your desired level. Please give the ame generator time to react

to the changes you make.

Once you have made your adjustments to both the ame height and crackling sound, the appliance will keep these

settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you

switch on the appliance, it will start up as normal, wait 45 seconds for the ames to start and then revert to the adjusted

settings.

Nozzle Inserts

Nozzle inserts have been supplied and tted to the nozzle opening. These inserts are used to alter the prole of the

ame effect. These inserts can be removed if a different ame prole is preferred. In addition to these inserts, inserts for

blocking the ame in certain areas have also been supplied. To t these inserts, remove the exisitng inserts that have

been supplied and tted to the product. Break the blocking inserts into the required length. Snap the inserts into the

nozzle opening in the desired location. See Fig 22 for further deatils.

LOW WATER / REFILLING THE WATER TANKS

When the water tanks have emptied and the water level in the product is getting low, the product will ash its LEDs twice

and beep twice. The product will operate for a further 15 minutes before beeping once and switching into low water

mode. For products being operated with the LED log fuel bed, the fuel bed will remain illuminated while in low water

mode. At this point, the product can either be switched into stand-by mode using the remote control or Bluetooth receiver

or the product can be relled with water. Relling the product with water will cause the product to restart automatically.

To rell the tank, remove the fuel bed and remove the water tank from its position on top of the sump. Rell the water tank

using ltered/decalcied water only. The tank can then be replaced on top of the sump. If the product was not switched

into stand-by mode after experiencing low later, the product will restart automatically after about 20 seconds of relling.

Please note that for a CAS1000R product, the side of the product that is experiencing low water will ash twice and beep

twice. The water tanks on both sides of the CAS1000R product can be relled at this point as it is likely that they should

both be empty or near empty.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Dimplex CAS 1000R Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info